Under the Energy Independence and Security Act of 2007 (EISA), the National Institute of Standards and Technology (NIST) was assigned “primary responsibility to coordinate development of a framework that includes protocols and model standards for information management to achieve interoperability of Smart Grid devices and systems…” [EISA Section 1305]. 35 This responsibility comes at a time when the electric power grid and electric power industry are undergoing the most dramatic TransforMATion in many decades. Very significant investments are being made by industry and the federal government to modernize the power grid. To realize the full benefits of these investments—and the continued investments forecast for the coming decades—there is a continued need to establish effective smart grid 36 standards and protocols for interoperability.
標簽： Framework Roadmap NIST and
上傳時間： 2020-06-07
上傳用戶：shancjb
Power Electronics is one of modern and key technologies in Electrical and Electronics Engineering for green power, sustainable energy systems, and smart grids. Especially, the TransforMATion of existing electric power systems into smart grids is currently a global trend. The gradual increase of distributed generators in smart grids indicates a wide and important role for power electronic converters in the electric power system, also with the increased use of power electronics devices (nonlinear loads) and motor loadings, low cost, low-loss and high-performance shunt current quality compensators are highly demanded by power customers to solve current quality problems caused by those loadings.
標簽： Electronics Parallel Filters Power
上傳時間： 2020-06-07
上傳用戶：shancjb
以倉庫智能改造為背景,主要介紹單片機和上位機之間通信網絡和通信協議的選擇,MODBUS協議通信指令和功能碼使用,重點闡述了基于RS-485總線的MODBUS通信協議在上位機和單片機之間的串行通信,實現上位機對單片機設備的遠程控制和信息采集的功能。Based on the intelligent warehouse TransforMATion as the background,mainly introduces between MCU and PC communication network and the choice of communication protocol,instruction and the function code using the MODBUS protocol communication,expounds the MODBUS communication protocol based on RS-485 bus serial communication between PC and single chip microcomputer,PC remote control of single chip computer equipment and the function of information collection.
標簽： RS-485總線 modbus 單片機
上傳時間： 2022-03-26
上傳用戶：
基于DSP28035的高速永磁無刷直流電機驅動系統，包括論文和軟硬設計資料。摘要參賽作品為基于DSP28035的高速永磁無刷直流電機驅動系統。該系統以一臺額定轉速60 krpm的高速永磁無刷直流電機、交錯并聯的Buck電路以及全橋電路為硬件平臺，以DSP28035為控制核心，實現了調壓調速功能和基于坐標變換的無位置傳感器新技術。為實現該系統要求，本作品充分利用了DSP28035的資源例如：CLA模塊，模擬比較器、HPWM模塊以及AD轉換模塊等。AbstractThis work is the drive system for a high speed permanent magnet burshless dc motor based on DSP28035. The hardware platform consists of a BLDC motor(rated speed is 60000rpm), a Buck circuit and an inverter. Under the control of DSP28035, this system can achieve the goal of adjusting the motor’s speed with voltage and the function of sensorless control based on the coordinate TransforMATion. By making full use of resources of the core, such as CLA, analog comparator, HPWM and AD converters, the whole system can meet the requirements.1 引言高速永磁無刷直流電機驅動系統由于基波頻率較高（一般在1kHZ以上），利用逆變橋斬波進行調速的控制方式通常會受到開關管開關頻率的限制，因此該系統多采用三相全橋前級加Buck電路進承擔調壓調速的功能，而三相全橋主要承擔邏輯換相的功能。然而，傳統Buck電路所需電感的體積較大，增加了系統的體積，降低了系統的功率密度。
上傳時間： 2022-05-08
上傳用戶：bluedrops
蟲蟲下載站版權所有 京ICP備2021023401號-1
