This m file models a DPSK UWB system using a delay in one leg of the mixer, correlation receiver low pass filter combination requiring no template for synching. Various waveforms are displayed throughout the system to allow the user to observe operation of the system.
The idea behind differential GPS is to remove as much errors as possible from the range measurements by establishing these errors at a reference site. In its most simple setup, a GPS receiver is located at a well surveyed position and its (pseudo) range measurements are compared with the actual calculated range from this receiver to the SV s. The differences between measured ranges and calculated ranges at the reference receiver are applied as corrections to the ranges measured by other receiver(s) close by.
In this project we analyze and design the minimum mean-square error (MMSE) multiuser receiver for uniformly quantized synchronous code division multiple access (CDMA) signals in additive white Gaussian noise (AWGN) channels.This project is mainly based on the representation of uniform quantizer by gain plus additive noise model. Based on this model, we derive the weight vector and the output signal-to-interference ratio (SIR) of the MMSE receiver. The effects of quantization on the MMSE receiver performance is characterized in a single parameter named 鈥漞quivalent noise variance鈥? The optimal quantizer stepsize which maximizes the MMSE receiver output SNR is also determined.
Introduction
Matlab is an ideal tool for simulating digital communications systems, thanks to
its easy scripting language and excellent data visualization capabilities. One of the
most frequent simulation tasks in the field of digital communications is bit-error-
rate testing of modems. The bit-error-rate performance of a receiver is a figure of
merit that allows different designs to be compared in a fair manner. Performing
bit-error-rate testing withMatlab is very simple, but does require some prerequisite
knowledge.
A combined space鈥搕ime block coding (STBC) and eigen-space tracking
(EST) scheme in multiple-input-multiple-output systems is
proposed. It is proved that the STBC-EST is capable of shifting
hardware complexity from the receiver to the transmitter without
any bit error rate (BER) performance loss. A computation efficient
EST algorithm is also proposed, which makes the STBC-EST affordable.
Simulation results show that the STBC-EST with a modest
feedback requirement results in a negligible BER performance loss
compared with a dual system configuration.
This file is distributed in the hope that it will be useful, but WITHOUT
WARRANTY OF ANY KIND.
Author(s): Ole Saether
DESCRIPTION:
This example should be used together with ex2a-tx433.asm. One nRF9E5
evaluation board (receiver) should be programmed with the hex-file generated
from assembling this file and the other evaluation board (transmitter)
programmed with the hex-file generated from assembling ex2a-tx433.asm.
All switches on the DIP-swith S206 on the receiver must be set to the "on"
position and all switches on the DIP-swith S205 on the transmitter must be
set to the "on" position.
When one of the switched SW1-SW4 on the transmitter is pressed the
corresponding LED on the receiver is turned on.
The functionality is the same as in ex2c-rx.c.
In 揚erformance of multi-carrier DS CDMA Systems?we apply a multi-carrier signaling technique to a direct-sequence CDMA system, where a data sequence multiplied by a spreading sequence modulates multiple carriers, rather than a single carrier. The receiver provides a correlator for each carrier, and the outputs of the correlators are combined with a maximal-ratio combiner. This type of signaling has the desirable properties of exhibiting a narrowband interference suppression effect, along with robustness to fading, without requiring the use of either an explicit RAKE structure or an interference suppression filter.
This program is ICQ SMS Receiver. You have certainly seen that almost every web site provides an option to send e-mail to that web site s owner. But what about SMS? It is now also possible, if your mobile phone service provider supported by ICQ
OSCILLATORS are key building blocks in integrated transceivers. In wired and
wireless communication terminals, the receiver front-end selects, amplifies and
converts the desired high-frequency signal to baseband. At baseband the signal can
then be converted into the digital domain for further data processing and demodula-
tion. The transmitter front-end converts an analog baseband signal to a suitable high-
frequency signal that can be transmitted over the wired or wireless channel.
A wireless communication network can be viewed as a collection of nodes, located in some domain, which
can in turn be transmitters or receivers (depending on the network considered, nodes may be mobile users,
base stations in a cellular network, access points of a WiFi mesh etc.). At a given time, several nodes
transmit simultaneously, each toward its own receiver. Each transmitter–receiver pair requires its own
wireless link. The signal received from the link transmitter may be jammed by the signals received from
the other transmitters. Even in the simplest model where the signal power radiated from a point decays in
an isotropic way with Euclidean distance, the geometry of the locations of the nodes plays a key role since
it determines the signal to interference and noise ratio (SINR) at each receiver and hence the possibility of
establishing simultaneously this collection of links at a given bit rate. The interference seen by a receiver is
the sum of the signal powers received from all transmitters, except its own transmitter.
