基于TMS320F2812 光伏并網發電模擬裝置PROTEL設計原理圖+PCB+軟件源碼+WORD論文文檔,硬件采用2層板設計，PROTEL99SE 設計的工程文件，包括完整的原理圖和PCB文件，可以做為你的學習設計參考。 摘要：本文實現了一個基于TMS320F2812 DSP芯片的光伏并網發電模擬裝置，采用直流穩壓源和滑動變阻器來模擬光伏電池。通過TMS320F2812 DSP芯片ADC模塊實時采樣模擬電網電壓的正弦參考信號、光伏電池輸出電壓、負載電壓電流反饋信號等。經過數據處理后，用PWM模塊產生實時的SPWM 波，控制MOSFET逆變全橋輸出正弦波。本文用PI控制算法實現了輸出信號對給定模擬電網電壓的正弦參考信號的頻率和相位跟蹤，用恒定電壓法實現了光伏電池最大功率點跟蹤（MPPT），從而達到模擬并網的效果。另外本裝置還實現了光伏電池輸出欠壓、負載過流保護功能以及光伏電池輸出欠壓、過流保護自恢復功能、聲光報警功能、孤島效應的檢測、保護與自恢復功能。系統測試結果表明本設計完全滿定設計要求。關鍵詞：光伏并網，MPPT，DSP Photovoltaic Grid-connected generation simulator Zhangyuxin，Tantiancheng，Xiewuyang(College of Electrical Engineering, Chongqing University)Abstract: This paper presents a photovoltaic grid-connected generation simulator which is based on TMS320F2812 DSP, with a DC voltage source and a variable resistor to simulate the characteristic of photovoltaic cells. We use the internal AD converter to real-time sampling the referenced grid voltage signal, outputting voltage of photovoltaic, feedback outputting voltage and current signal. The PWM module generates SVPWM according to the calculation of the real-time sampling data, to control the full MOSFET inverter bridge output sine wave. We realized that the output voltage of the simulator can track the frequency and phase of the referenced grid voltage with PI regulation, and the maximum photovoltaic power tracking with constant voltage regulation, thereby achieved the purpose of grid-connected simulation. Additionally, this device has the over-voltage and over-current protection, audible and visual alarm, islanding detecting and protection, and it can recover automatically. The testing shows that our design is feasible.Keywords: Photovoltaic Grid-connected，MPPT，DSP 目錄引言 11. 方案論證 11.1. 總體介紹 11.2. 光伏電池模擬裝置 11.3. DC-AC逆變橋 11.4. MOSFET驅動電路方案 21.5. 逆變電路的變頻控制方案 22. 理論分析與計算 22.1. SPWM產生 22.1.1. 規則采樣法 22.1.2. SPWM 脈沖的計算公式 32.1.3. SPWM 脈沖計算公式中的參數計算 32.1.4. TMS320F2812 DSP控制器的事件管理單元 42.1.5. 軟件設計方法 62.2. MPPT的控制方法與參數計算 72.3. 同頻、同相的控制方法和參數計算 8
Precision, Low Noise, CMOS, Rail-to-Rail,
Input/Output Operational Amplifiers
Data Sheet AD8605/AD8606/AD8608The AD8605, AD8606, and AD86081 are single, dual, and quad rail-to-rail input and output, single-supply amplifiers. They feature very low offset voltage, low input voltage and current noise, and wide signal bandwidth. They use the Analog Devices, Inc. patented DigiTrim? trimming technique, which achieves
The PW5410B is a low noise, constant frequency (1.2MHz) switched capacitor voltage doubler. Itproduces a regulated output voltage from 1.8V to 5V input with up to 100mA of output current. Lowexternal parts count (one flying capacitor and two small bypass capacitors at VIN and VOUT) makethe PW5410B ideally suited for small, battery-powered applications
The PW5410A is a low noise, constant frequency (1.2MHz) switched capacitor voltage doubler. Itproduces a regulated output voltage from 2.7V to 5V input with up to 250mA of output current. Lowexternal parts count (one flying capacitor and two small bypass capacitors at VIN and VOUT) makethe PW5410A ideally suited for small, battery-powered applications
PW2330 develops a high efficiency synchronous step down DC-DC converter capable of delivering3A output current. PW2330 operates over a wide input voltage range from 4.5V to 30V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. PW2330 adopts the proprietary instant PWM architecture to achieve fast transient responsesfor high step down applications and high efficiency at light loads. In addition, it operates atpseudo-constant frequency of 500kHz under continuous conduction mode to minimize the size ofinductor and capacitor
The PW2228A is a high efficiency single inductor Buck-Boost converter which can supply theload current up to 1.5A. It provides auto-transition between Buck and Boost Mode. The PW2228Aoperates at 2.4MHz switching frequency in CCM. DC/DC converter operates at Pulse-Skipping Modeat light load. The output voltage is programmable using an external resistor divider, or is fixed to3.3V internally. The load is disconnected from the VIN during shutdown.The PW2228A is available in TDFN3X3-10 package.
PW2205 develops a high efficiency synchronous step-down DC-DC converter capable of delivering5A output current. PW2205 operates over a wide input voltage range from 4.5V to 30V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss.PW2205 adopts the instant PWM architecture to achieve fast transient responses for high step downapplications and high efficiency at light loads. In addition, it operates at pseudo-constant frequencyof 500kHz under continuous conduction mode to minimize the size of inductor and capacitor
The PW2163 is a high efficiency 500 kHz synchronous step-down DC-DC converter capable ofdelivering 3A current. The PW2163 operates over a wide input voltage range from 4.5V to 18V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. Low output voltage ripple and small external inductor and capacitor sizes are achieved with 500kHz switching frequency. It adopts the instant PWM architecture to achieve fast transient responsesfor high step down applications
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
