\r\n經典的Protel99se入門教程，孫輝著北京郵電大學出版社出版
上傳時間： 2013-09-11
上傳用戶：Yukiseop
gerber-to-protel is a pdf file ,which is used for convert bmp to pcb.
標簽： gerber-to-protel file is
上傳時間： 2013-09-18
上傳用戶：liuxinyu2016
protel_lib-PIC16 is a protel lib file.
標簽： protel_lib-PIC protel file lib
上傳時間： 2013-09-18
上傳用戶：hn891122
PROTEUS仿真用單片機系統板\r\n系統資源豐富：\r\n★ 內置RAM 32KB模塊\r\n★ 內置8位動態數碼顯示模塊\r\n★ 內置8X8點陣顯示模塊\r\n★ 4位靜態數碼顯示模塊\r\n★ 4位級聯的74LS164串并轉換模塊\r\n★ 內置8通道8位A/D轉換\r\n★ 內置8位D/A轉換\r\n★ 內置2路SPI和I2C總線接口\r\n★ 內置4路1－Wire總線接口\r\n★ 內置4X4矩陣式鍵盤\r\n★ 內置4路獨立式鍵盤\r\n★ 內置4路撥動開關\r\n★ 內置8位LED發光二
上傳時間： 2013-09-30
上傳用戶：sssl
在軟件Proteus中仿真ucos（ARM）\r\n1.移植除了OS_CPU.h,OS_CPU_A.s,OS_CPU_C.C 三個函數外，對中斷專門用了一個函數OS_int_A.s 按其中的規則寫中斷函數即可. \r\n2。應用實例為\\ArmUCOS\\App\\test1\\test.mcp,在周立功2104的板子上的ram中就可直接運行(code＋data
上傳時間： 2013-09-30
上傳用戶：s363994250
This document was developed under the Standard Hardware and Reliability Program (SHARP) TechnologyIndependent Representation of Electronic Products (TIREP) project. It is intended for use by VHSIC HardwareDescription Language (VHDL) design engineers and is offered as guidance for the development of VHDL modelswhich are compliant with the VHDL Data Item Description (DID DI-EGDS-80811) and which can be providedto manufacturing engineering personnel for the development of production data and the subsequent productionof hardware. Most VHDL modeling performed to date has been concentrated at either the component level orat the conceptual system level. The assembly and sub-assembly levels have been largely disregarded. Under theSHARP TIREP project, an attempt has been made to help close this gap. The TIREP models are based upon lowcomplexity Standard Electronic Modules (SEM) of the format A configuration. Although these modules are quitesimple, it is felt that the lessons learned offer guidance which can readily be applied to a wide range of assemblytypes and complexities.
上傳時間： 2014-12-23
上傳用戶：xinhaoshan2016
Methods for designing a maintenance simulation training system for certain kind of radio are introduced. Fault modeling method is used to establish the fault database. The system sets up some typical failures， follow the prompts trainers can locate the fault source and confirm the type to accomplish corresponding fault maintenance training. A training evaluation means is given to examining and evaluating the training performance. The system intuitively and vividly shows the fault maintenance process， it can not only be used in teaching， but also in daily maintenance training to efficiently improve the maintenance operation level. Graphical programming language LabVIEW is used to develop the system platform.
上傳時間： 2013-11-19
上傳用戶：3294322651
常用D/A轉換器和A/D轉換器介紹 下面我們介紹一下其它常用D/A轉換器和 A/D 轉換器，便于同學們設計時使用。 1. DAC0808 圖 1 所示為權電流型 D/A 轉換器 DAC0808 的電路結構框圖。用 DAC0808 這類器件構 成的 D/A轉換器，需要外接運算放大器和產生基準電流用的電阻。DAC0808 構成的典型應用電路如圖2 所示。
標簽： 轉換器
上傳時間： 2014-12-23
上傳用戶：zhenyushaw
The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsrail-to-rail operation and presents a 100kI (typ) load toan external reference.
上傳時間： 2013-12-23
上傳用戶：ArmKing88
The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these switches combine high-voltage bilateral MOSswitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
上傳時間： 2013-10-09
上傳用戶：yepeng139
<rt id="8i8iu"></rt>