現有基于MAX7219芯片的數碼管驅動電路只適用于小尺寸LED，為擴展其使用范圍，在介紹動態顯示芯片MAX7219功能的基礎上，提出了一個基于該芯片的8位高亮度8英寸數碼管驅動電路。電路保留了MAX7219芯片的功能強大、編程簡單等優點，通過74LS273鎖存器和ULN2803達林頓驅動器，實現了對任意大尺寸數碼管提供較高電壓和電流驅動的靜態顯示，并亮度可調。 Abstract: The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
標簽： 7219 MAX LED 數碼顯示
上傳時間： 2013-10-23
上傳用戶：31633073
設計了一種基于PIC16C71單片機的數字水溫配制閥。該配制閥采用NTC熱敏電阻作溫度傳感器，與固定電阻組成簡單分壓電路作為水溫測量電路，利用PIC16C71單片機內置的8位A/D轉換器把熱敏電阻上的模擬電壓轉換為數字量，PIC16C71單片機控制直流電機驅動混水閥調節冷熱水的混合比例實現水溫調節。給出了控制電路圖，對水溫測量電路的參數選擇和測溫精度作了詳細討論。實驗和分析表明，選用阻值較大的NTC熱敏電阻和分壓電阻可較好地解決熱敏電阻因功耗較大造成的熱擊穿問題。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上傳時間： 2013-11-08
上傳用戶：Yue Zhong
針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
標簽： 單片機 B超 數字化 鍵盤設計
上傳時間： 2013-10-10
上傳用戶：asdfasdfd
在航電系統維護過程中，為解決定位故障的效率和降低維修成本等問題，提出了基于ICD（Interface Control Document，接口控制文件）的1553B總線的信息監控系統模型。該系統運用數據采集卡對總線中傳輸?shù)男盘?hào)有無失真、偏差等電氣特性進行檢測，并使用1553B通訊卡通過測控軟件LabWindows/CVI編程與ICD數據庫的動態鏈接，實現總線信息的解析和故障的判斷。與傳統的維護過程相比，這種模型能夠從信號的電氣特性以及信息的解析等全方位的去檢測判斷故障的來源，并且能夠廣泛在其他1553B總線系統內擴展應用。驗證表明該監控系統可以對總線信息進行快速有效地監測分析，能滿足應用需求。 Abstract: In the process of avionics system maintenance， to solve the problems such as improving the efficiency of fast orientation to troubles and reducing maintenance cost， system of 1553B bus information monitor model based on ICD was proposed. The system observed whether the data which transmitted on the bus appear distortion and deviation by using data acquisition card. And using 1553B communication card programming of the measure software LabWindows/CVI and the dynamic linking of ICD database， message analysis and fault estimation could be realized. Compared with traditional maintenance， this model can all-dimensionally detect and analyze the source of faults from both electrical characteristics of the signal and message analysis， and it can be widely applied in the other 1553B system. Experiment shown that this monitor system can effectively detect and analyze the bus message and can meet the application requirements.
標簽： 1553B 總線 信息監控
上傳時間： 2013-11-23
上傳用戶：18752787361
為了有效地提升鉛酸蓄電池的使用壽命，同時實現對充電過程的監控，設計出一種用單片機控制的36 V鉛酸蓄電池充電電源。本電路采用反激式拓?fù)洌B續電流工作模式，電源管理IC設計在電源的副邊，由ELAN公司的EM78P258N單片機模擬，是用可編程器件模擬電源管理IC，實現智能電源低成本化的一次成功嘗試，通過對單片機的軟件設計實現了充電電源的狀態顯示、充電時間控制、報警、過溫保護、過壓保護、過流保護等功能。本充電器真正的實現了鉛酸蓄電池的三段式充電過程，其最高輸出功率可達90 W，效率約85%，成本不到20元，具有很高的市場競爭力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
標簽： 單片機控制 充電電源 鉛酸蓄電池
上傳時間： 2013-11-16
上傳用戶：cepsypeng
以C8051F020為核心處理器，設計無線傳感器網絡數據采集系統。系統采用SZ05-ADV型無線通訊模塊組建Zigbee無線網絡，結合嵌入式系統的軟硬件技術，完成終端節點的8路傳感器信號的數據采集。現場8路信號通過前端處理后，分別送入C8051F020的12位A/D轉換器進行轉換。經過精確處理、存儲后的現場數據，通過Zigbee無線網絡傳送到上位機，系統可達到汽車試驗中無線測試的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
標簽： C8051F020 Zigbee 汽車測試 系統設計
上傳時間： 2013-11-23
上傳用戶：dsgkjgkjg
提出一種基于凌陽單片機的步進電機加減速的控制方法。采用凌陽科技推出的16位結構工控單片機SPMC75F2413A為控制器，由Allegro公司生產的兩相步進電機專用驅動器件SLA7042M構成步進電機的驅動電路，在傳統的3段直線加減速控制算法基礎上增加至7段S形曲線加減速過程，控制步進電機的啟動和停止。實驗結果表明，該控制方法克服了直線加減速中不連續、易造成系統沖擊的問題，整個系統實現柔性控制，電機啟動、停止連續性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
標簽： 凌陽單片機 步進電機 減 控制方法
上傳時間： 2013-12-08
上傳用戶：jiangfire
單片機作為一種微型計算機，其內部具有一定的存儲單元（8031除外），但由于其內部存儲單元及端口有限，很多情況下難以滿足實際需求。為此介紹一種新的擴展方法，將數據線與地址線合并使用，通過軟件控制的方法實現數據線與地址線功能的分時轉換，數據線不僅用于傳送數據信號，還可作為地址線、控制線，用于傳送地址信號和控制信號，從而實現單片機與存儲器件的有效連接。以單片機片外256KB數據存儲空間的擴展為例，通過該擴展方法，僅用10個I/O端口便可實現，與傳統的擴展方法相比，可節約8個I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
標簽： 單片機 P0口 數據存儲器 擴展
上傳時間： 2014-12-26
上傳用戶：adada
為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
標簽： 單總線 無線溫度 采集 系統設計
上傳時間： 2013-10-29
上傳用戶：515414293
針對目前汽車追尾事件頻發問題，提出一種防汽車車前和車后追尾的安全裝置設計。該設計以高性能、低功耗的8位AVR微處理器ATmega8L為核心，結合霍爾式車速傳感器、激光雷達測距裝置和MMA7260QT加速度傳感器，能夠兼顧車前和車后，摒棄以往設計中只考慮車前或車后單一性缺點，尤其適用于高速、夜晚或新手行車。 Abstract: Aiming at the high frequency of vehicle rear-end collision，a safe device design of anti-vehicle rear-end collision is presented.In the design，the high-performance，low-power8-bit AVR microprocessor ATmega8L is utilized as a core combined with Hall-type speed sensor，laser-radar ranging devices and the acceleration sensor MMA7260QT.The design considers both the front and back of a car，and overcomes the drawbacks of former designs in which only the front or the back of the car is considered，so it is especially suitable for high-speed，night or the beginner’s driving.
上傳時間： 2013-10-14
上傳用戶：GavinNeko
蟲蟲下載站版權所有 京ICP備2021023401號-1
