8051上的CRC8校驗 A CCITT-8 CRC calculator. The source contains both the calculated (smaller but slower) version, and the table driven (faster but larger) version.
Example - 3-D Stem Plot of an FFTFor example, fast Fourier transforms are calculated at points around the unit circle on the complex plane. So, it is interesting to visualize the plot around the unit circle. Calculating the unit circle.
Wavelet Subband coding for speaker recognition
The fn will calculated subband energes as given in the att tech paper of ruhi sarikaya and others. the fn also calculates the DCT part. using this fn and other algo for pattern classification(VQ,GMM) speaker identification could be achived. the progress in extraction is also indicated by progress bar.
·詳細說明：MPEG4解壓縮算法源代碼，研究其中關于錯誤處理部分。-MPEG4 solution compression calculated the law origin code, studies about the error processing part. 文件列表(點擊判斷是否您需要的文件): DECORE ......\BUILD .
Calculation of the Differential Impedance of Tracks on FR4 substrates
There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.
生活中許多目標的高度和水平距離需要進行測量。目前主要的測量方法，仍以傳統的皮尺丈量為主，測量效率不高，有時還很不方便，沒有技術成熟的數字式測高測距產品。以基本的數學方法為理論依據，利用遙控小車做為載體，采用角度傳感器測量角度、霍爾傳感器測量水平距離等，通過單片機LM3S615進行數據計算，實現了對待測目標物體的高度、水平距離等數據的快速、精確和數字式的測量，高度測量精度可達99.06%，水平測量精度則可達98.06%。
Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
將現行的供暖計費方式由按建筑面積計費變為按消耗的熱能計費是供暖計費方式發展趨勢，為了滿足這一計費方式變化的需要，設計了基于IC卡的預付費式新型供暖計費系統，通過測量用戶采暖系統進出口的溫度和流量，計算用戶消耗的熱能，利用IC卡記錄用戶預付費的金額和當年熱能的單價，根據熱能消耗和當年熱能的單價計算用戶采暖費，根據實際發生的供暖費用和預付費金額控制供暖的開停，這一計費方式的變化使供暖計費更趨合理。
Abstract:
It is trend that the mode of heat charging is changed from billing by building area to by thermal energy. In order to meet the needs of heat charging mode changing， a new system of heat charging based on IC card is proposed. The user?蒺s energy consumption is calculated by measuring the user inlet and outlet temperature and flow，using the IC card to record the prepaid amount and the current price of heat. The user?蒺s heating costs is calculated according to energy consumption and current price， according to actual heating costs and prepaid amount，the system controls the heating opening or stopping. It is more reasonable that calculated heating costs by user heat consumption
Calculation of the Differential Impedance of Tracks on FR4 substrates
There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
