提出一種基于凌陽單片機的步進電機加減速的控制方法。采用凌陽科技推出的16位結構工控單片機SPMC75F2413A為控制器，由Allegro公司生產的兩相步進電機專用驅動器件SLA7042M構成步進電機的驅動電路，在傳統的3段直線加減速控制算法基礎上增加至7段S形曲線加減速過程，控制步進電機的啟動和停止。實驗結果表明，該控制方法克服了直線加減速中不連續、易造成系統沖擊的問題，整個系統實現柔性控制，電機啟動、停止連續性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
標簽： 凌陽單片機 步進電機 減 控制方法
上傳時間： 2013-12-08
上傳用戶：jiangfire
在深入了解Flash存儲器的基礎上，采用單片機自動檢測存儲器無效塊。主要通過讀取每一塊的第1、第2頁內容，判斷該塊的好壞，并給出具體的實現過程，以及部分關鍵的電路原理圖和C語言程序代碼。該設計最終實現單片機自動檢測Flash壞塊的功能，并通過讀取ID號檢測Flash的性能，同時該設計能夠存儲和讀取1GB數據。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
標簽： Flash 單片機 存儲器 自動檢測
上傳時間： 2013-10-25
上傳用戶：taozhihua1314
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸?shù)慕涌陔娐吩韴D。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
標簽： 工控軟件 單片機 串口通訊 多機
上傳時間： 2013-12-19
上傳用戶：tecman
實時時鐘是微機保護裝置的重要部件，在討論P(yáng)CF8583結構與功能的基礎上，提出采用dsPIC33F系列微處理器與串行I2C時鐘PCF8583的接口設計方案，給出了相應的接口電路與軟件流程。該設計方案結構簡單，可靠性高，開發周期短，具有一定的實用與參考價值。所設計的微機保護裝置已投入現場運行，效果良好。 Abstract: Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
標簽： 8583 PCF 串行時鐘 中的應用
上傳時間： 2013-11-18
上傳用戶：Thuan
設計一種基于AT89C52的語音錄放系統，利用單片機、ISD2560語音錄放器件、麥克風、揚聲器等元器件實現硬件電路的設計，并利用C51高級語言設計ISD2560器件控制字的寫入和定時中斷程序。經軟硬件調試，結果表明該系統錄放效果良好，具有一定的工程實用價值。 Abstract: Voice recording and playback system based on AT89C52is designed in this paper.Using the single-chip microcomputer，voice recording and playback chip ISD2560，microphone and speaker to realize the hardware circuit design.Writing ISD2560control words and timing interrupt procedures are designed by C51advanced language.Through the hardware and software test,voice recording and playback system play better voice,and this system has some engineering practical values.
上傳時間： 2013-10-20
上傳用戶：ywcftc277
MG3500SoC是支持H.264高清編解碼器的片上系統，內部集成一個嵌入式ARM926處理器，支持高清H.264編解碼、MPEG鄄2解碼和JPEG編解碼。介紹了MG3500SoC的主要性能特點、引腳排列、主要接口功能及在DVR上的應用，以及MG3500SoC及其周圍器件的硬件設計，提出了在設計中應注意的問題。 Abstract: The MG3500System-on-Chip（SoC）is high definition（HD）H.264codec,including ARM926-EJ processor，H.264encoder/decoder，MPEG2decoder and JPEG/MJPEG encoder/decoder.The features,pin assignments，interfaces and the typical application of MG3500in DVR are introduced in this paper.The application hardware circuit between the MG3500SoC and peripheral device are given,the questions which the syetem design needs to pay attention are explained.
上傳時間： 2013-11-12
上傳用戶：elinuxzj
介紹了以AVR單片機ATmega16為核心，采用前端信號調理電路、程控增益放大器以及波形顯示LCD（GDM12864A）實現的一個簡易示波器。并給出該系統設計的硬件和軟件設計方案。 Abstract: Abstract:This paper introduces an easy digital storage oscilloscope based on the AVR microcontroller ATmega16,especially emphasizes on the software design and the hardware design which contains signal processing circuit,gain-programmed amplifier circuit and LCD’s interface circuit and so on.
上傳時間： 2013-10-13
上傳用戶：ccccccc
介紹了當前普通標記機控制系統現狀及其存在缺點，給出氣動標記機及相頻修正PWM模式的工作原理。采用ATmega16單片機和USB轉換RS232接口器件CH341T實現驅動控制系統與PC的實時通訊，標記控制系統可升級到USB接口。采用基于ATmega16的相頻修正PWM替換555振蕩電路產生的PWM，可直接通過軟件調整PWM信號。使用達林頓三極管TIP122替代直流繼電器驅動高頻電磁閥，使得電磁閥驅動電路簡單，成本低廉。該控制系統已成功應用于氣動標記機。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
標簽： ATmega 16 標記 控制系統
上傳時間： 2013-10-18
上傳用戶：1427796291
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
標簽： C8051F020 單片機 多路 壓力
上傳時間： 2013-11-16
上傳用戶：yare
為滿足礦井安全生產要求，介紹了一種以AT89C51單片機為主控器，對環境空氣的溫度、有毒易燃?xì)怏w的濃度等進行檢測的監控系統。該系統配合外圍電路能實現對上述環境指標的控制并存儲相關數據與上位PC機通信。它采用硬件抗干擾和軟件抗干擾技術，以確保整個系統工作的準確性。 Abstract: In order to meet the needs of mine produce safety，a kind of intellignet mine ambient monotoring and control system based on AT89C51 is introduced.This system can detect the temperature of ambient of mine，the density of poisonous inflammable gas,combined external circuit.With its function part， this system can change above-mentioned elements.
上傳時間： 2013-11-10
上傳用戶：wendy15
蟲蟲下載站版權所有 京ICP備2021023401號-1
