Who has never experienced oscillations issues when using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
標簽： 半導體 運放 穩定性
上傳時間： 2013-10-28
上傳用戶：chenbhdt
模擬集成電路的設計與其說是一門技術，還不如說是一門藝術。它比數字集成電路設計需要更嚴格的分析和更豐富的直覺。嚴謹堅實的理論無疑是嚴格分析能力的基石，而設計者的實踐經驗無疑是誕生豐富直覺的源泉。這也正足初學者對學習模擬集成電路設計感到困惑并難以駕馭的根本原因。.美國加州大學洛杉機分校(UCLA)Razavi教授憑借著他在美國多所著名大學執教多年的豐富教學經驗和在世界知名頂級公司(AT&T，Bell Lab，HP)卓著的研究經歷為我們提供了這本優秀的教材。本書自2000午出版以來得到了國內外讀者的好評和青睞，被許多國際知名大學選為教科書。同時，由于原著者在世界知名頂級公司的豐富研究經歷，使本書也非常適合作為CMOS模擬集成電路設計或相關領域的研究人員和工程技術人員的參考書。... 本書介紹模擬CMOS集成電路的分析與設計。從直觀和嚴密的角度闡述了各種模擬電路的基本原理和概念，同時還闡述了在SOC中模擬電路設計遇到的新問題及電路技術的新發展。本書由淺入深，理論與實際結合，提供了大量現代工業中的設計實例。全書共18章。前10章介紹各種基本模塊和運放及其頻率響應和噪聲。第11章至第13章介紹帶隙基準、開關電容電路以及電路的非線性和失配的影響，第14、15章介紹振蕩器和鎖相環。第16章至18章介紹MOS器件的高階效應及其模型、CMOS制造工藝和混合信號電路的版圖與封裝。 1 Introduction to Analog Design 2 Basic MOS Device Physics 3 Single-Stage Amplifiers 4 Differential Amplifiers 5 Passive and Active Current Mirrors 6 Frequency Response of Amplifiers 7 Noise 8 Feedback 9 Operational Amplifiers 10 Stability and Frequency compensation 11 Bandgap References 12 Introduction to Switched-Capacitor Circuits 13 Nonlinearity and Mismatch 14 Oscillators 15 Phase-Locked Loops 16 Short-Channel Effects and Device Models 17 CMOS Processing Technology 18 Layout and Packaging
標簽： analog design cmos of
上傳時間： 2014-12-23
上傳用戶：杜瑩12345
特點（FEATURES） 精確度0.2%滿刻度±0.5℃（冷接點補償）（Accuracy 0.2%F.S.±0.5℃（CJC）） 高精確度冷接點溫度補償（CJC traceability＜±0.5℃（0-70℃）) 熱電偶誤差補償，與斷線保護功能（Sensor error compensation(offset) and burnout protection function）) 16 BIT 隔離類
上傳時間： 2014-12-24
上傳用戶：wojiaohs
DC/DC 升壓IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上傳時間： 2013-11-07
上傳用戶：3294322651
設計一種基于P89V51RD2的功率因數測量?jī)x，采用光電隔離器和專用數碼管驅動器。該測量?jī)x是以增強型單片機P89V51RD2為核心，大大簡化系統硬件設計。而軟件部分采用模塊化設計思想，采用中值濾波和小數補償算法，實現功率因數的高精度測量。實驗測試表明，該功率因數測量?jī)x測量精度高，運行穩定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上傳時間： 2014-12-27
上傳用戶：CHINA526
為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上傳時間： 2013-11-06
上傳用戶：yy_cn
介紹了用單片機C 語言實現無功補償中電容組循環投切的基本原理和算法，并舉例說明。關鍵詞：循環投切;C51;無功補償中圖分類號： TM76 文獻標識碼： BAbstract: This paper introduces the aplication of C51 in the controlling of capacitorsuits cycle powered to be on and off in reactive compensation.it illustrate thefondamental principle and algorithm with example.Key words: cycle powered to be on and off; C51; reactive compensation 為提高功率因數，往往采用補償電容的方法來實現。而電容器的容量是由實時功率因數與標準值進行比較來決定的，實時功率因數小于標準值時，需投入電容組，實時功率因數大于標準值時，則需切除電容組。投切方式的不合理，會對電容器造成損壞，現有的控制器多采用“順序投切”方式，在這種投切方式下排序在前的電容器組，先投后切；而后面的卻后投先切。這不僅使處于前面的電容組經常處于運行狀態，積累熱量不易散失，影響其使用壽命，而且使后面的投切開關經常動作，同樣減少壽命。合理的投切方式應為“循環投切”。這種投切方式使先投入的運行的電容組先退出，后投的后切除，從而使各組電容及投切開關使用機率均等，降低了電容組的平均運行溫度，減少了投切開關的動作次數，延長了其使用壽命。
標簽： C51 無功補償 循環 電容
上傳時間： 2014-12-27
上傳用戶：hopy
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
上傳時間： 2013-11-07
上傳用戶：xy@1314
在研究傳統家用燃?xì)鈭?bào)警器的基礎上，以ZigBee協議為平臺，構建mesh網狀網絡實現網絡化的智能語音報警系統。由于傳感器本身的溫度和實際環境溫度的影響，傳感器標定后采用軟件補償方法。為了減少系統費用，前端節點采用半功能節點設備，路由器和協調器采用全功能節點設備，構建mesh網絡所形成的家庭內部報警系統，通過通用的電話接口連接到外部的公用電話網絡，啟動語音模塊進行報警。實驗結果表明，在2.4 GHz頻率下傳輸，有墻等障礙物的情況下，節點的傳輸距離大約為35 m，能夠滿足家庭需要，且系統工作穩定，但在功耗方面仍需進一步改善。 Abstract: On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligent voice alarm system. Because of the sensor temperature and the actual environment temperature, this system design used software compensation after calibrating sensor. In order to reduce system cost, semi-functional node devices were used as front-end node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in case of walls and other obstacles by 2.4GHz frequency transmission, this is able to meet family needs and work steadily, but still needs further improvement in power consumption.
標簽： ZigBee 無線智能 家 報警系統
上傳時間： 2013-10-30
上傳用戶：swaylong
The AN10 begins with a survey of methods for measuring op amp settling time. This commentary develops into circuits for measuring settling time to 0.0005%. Construction details and results are presented. Appended sections cover oscilloscope overload limitations and amplifier frequency compensation.
標簽： 運算放大器 穩定時間 測量
上傳時間： 2013-11-14
上傳用戶：JIMMYCB001
蟲蟲下載站版權所有 京ICP備2021023401號-1
