Atmel AVR 單片機上網方案
The AVR Embedded Internet Toolkit is the fastest way to connect anyembedded design to the Internet. It includes an ATmega AVR microcontroller,dedicated hardware, and all required software protocols forconnecting to the Internet. The AVR Embedded Internet Toolkit is thefastest choice for getting started with embedded Internet and for developinga complete embedded application connected to the Internet.
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
The XPS Ethernetlite peripheral does not provide any mechanism to access the Ethernet PHYregisters. These registers are used to configure auto negotiation parameters and to obtain PHYstatus. This application note provides reference systems and associated software to accessPHY registers by connecting the serial management bus signals MDC and MDIO to GPIOswhich the software controls directly.
VerboseGC demonstrates the use of the java.lang.management API to
print the garbage collection statistics and memory usage remotely
by connecting to a JMX agent with a JMX service URL:
service:jmx:rmi:///jndi/rmi://<hostName>:<portNum>/jmxrmi
where <hostName> is the hostname and <portNum> is the port number
to which the JMX agent will be connected.
Contents at a Glance
Introduction 1
PART I INSTALLATION AND CONFIGURATION 5
Hour 1 Preparing to Install Linux 7
2 Installing Linux 23
3 Post-Installation Issues 41
PART II LEARNING LINUX BASICS 67
Hour 4 Reading and Navigation Commands 69
5 Manipulation and Searching Commands 93
6 Using the Shell 117
7 Using the X Window System 143
8 Exploring the K Desktop Environment 177
PART III connecting TO THE OUTSIDE WORLD 197
Hour 9 Using Communications Programs 199
10 connecting to the Internet 223
11 Configuring Internet Email 249
12 Configuring Internet News 269
13 Internet Downloading and Browsing 289
ST7787 芯片的SPEC，比亞迪2.4inchLCM的SPEC。The ST7787 is a single-chip controller/driver for 262K-color, graphic type TFT-LCD. It consists of 720 source line and
320 gate line driving circuits. This chip is capable of connecting directly to an external microprocessor, and accepts Serial
Peripheral Interface (SPI), 8-bits/9-bits/16-bits/18-bits parallel interface. Display data can be stored in the on-chip display
data RAM of 240x320x18 bits. It can perform display data RAM read/write operation with no external operation clock to
minimize power consumption. In addition, because of the integrated power supply circuits necessary to drive liquid crystal,
it is possible to make a display system with the fewest components.
Bootloading the TMS320VC5506/C5507/C5509 A digital signal processor (DSP)
through the on-chip universal serial bus (USB) peripheral is part of the standard
bootloader provided on the device. This document describes the procedures for
physically connecting the DSP to a USB host, invoking the USB bootloader on the
DSP, generating the correct boot table file, and downloading the boot table from the
host to the DSP via USB.
The main MIPS processor of SMP8630 comes with a JTAG interface, allowing:
access to caches and data bus (DRAM) with a bandwidth of about 200kbit/s
examining the processor state whatever the execution mode (monice)
connecting to monice using mdi-server and using a gdb client on the processor to step and break
accurately whatever the execution mode
running semi-hosted applications
fl ash write tool
memory testing (MT command)
real-time traces: has not been built in CPU (Config3_TL=0) and only supported by MajicPLUS probes
(maybe built into emulator?)
