Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上傳時間： 2014-01-18
上傳用戶：wenyuoo
Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上傳時間： 2014-01-20
上傳用戶：wettetw
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power switches and supporting circuitry.These highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
上傳時間： 2013-10-22
上傳用戶：ztj182002
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上傳時間： 2013-10-31
上傳用戶：wwwe
A recent trend in the design of portable devices has beento use ceramic capacitors to filter DC/DC converter inputs.Ceramic capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic capacitors due to shortages oftantalum capacitors.
上傳時間： 2013-11-05
上傳用戶：comer1123
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上傳時間： 2013-10-10
上傳用戶：adada
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上傳時間： 2013-10-10
上傳用戶：1184599859
利用推挽正激變換技術設計了DC /DC開關電源。提出了基于推挽正激變換技術的電源電路拓撲和結構,闡述了該開關電源的工作及控制原理,并利用PSp ice軟件對該電路拓撲進行了仿真。實驗結果表明,該開關電源輸出穩定、波形理想。
上傳時間： 2013-10-21
上傳用戶：363186
概述 直流—直流電源模塊，是多路直流輸出穩壓電源.輸出功率最大可達162.4W，工作效率為75%，各路輸出均有限流、短路保護功能。封裝形式為鋁外殼結構。
上傳時間： 2013-11-06
上傳用戶：爺的氣質
摘要：在一種通訊解決方案中，由于用到各種不同的集成IC，往往需要多種不同的供電電壓，出于成本考慮以及系統集成，電源不能用多種不同電壓的直流電源來供電，因此需要特定的DC/DC芯片來解決這些問題，以實現電源電壓的升或者降，來提供不同的輸出電源，供各種芯片使用，本文講述的是3.3V到12V的升壓實現方案。關鍵詞：DC/DC，LM3224，PWM，開關
上傳時間： 2014-01-18
上傳用戶：cazjing
