In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during dc to dc conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上傳時間： 2013-11-24
上傳用戶：defghi010
A recent trend in the design of portable devices has beento use ceramic capacitors to filter dc/dc converter inputs.Ceramic capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic capacitors due to shortages oftantalum capacitors.
上傳時間： 2013-11-05
上傳用戶：comer1123
The LTM4600 dc/dc μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上傳時間： 2013-10-10
上傳用戶：adada
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdowndc/dc regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上傳時間： 2014-01-18
上傳用戶：laomv123
The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a dc/dcconverter. The systemdesigner often has a limited area in which to place the dc/dc converter; associated inductors and capacitors must be
上傳時間： 2013-11-23
上傳用戶：wys0120
當前，太陽能光伏市場(包括光伏模塊和逆變器)正以每年約30%的年累積速 度增長。太陽能逆變器的作用是將隨太陽能輻射及光照變化的dc 電壓轉換成為 電網兼容的AC 輸出；而對于廣大電子工程師而言，太陽能逆變器是一個值得高 度關注的技術領域。因此下文將介紹太陽能逆變器設計所需注意的技術要點、挑 戰以及相應的解決方法。 基本設計標準 基于太陽能逆變器的專用性以及保持設計的高效率，它需要持續監視太陽能 電池板陣列的電壓和電流，從而了解太陽能電池板陣列的瞬時輸出功率。它還需 要一個電流控制的反饋環，用于確保太陽能電池板陣列工作在最大輸出功率點， 以應付多變的高輸入。目前，太陽能逆變器已有多種拓撲結構，最常見的是用于 單相的半橋、全橋和Heric(Sunways 專利)逆變器，以及用于三相的六脈沖橋和 中點鉗位（NPC）逆變器；圖1 所示是這些逆變器的拓撲圖(Microsemi 圖源)。 同時，設計還需遵從安全規范，并在電網發生故障的時候可以快速斷開與電網的 連接。因此，太陽能逆變器的基本設計標準包括額定電壓、容量、效率、電池能 效、輸出AC 電源質量、最大功率點跟蹤（MPPT）效能、通信特性和安全性
標簽： 太陽能逆變器
上傳時間： 2014-12-24
上傳用戶：三人用菜
為解決直流逆變交流的問題，有效地利用能源，讓電源輸出最大功率，設計了高性能的基于IR2101最大功率跟蹤逆變器，并以SPMC75F2413A單片機作為主控制器。高電壓、高速功率的MOSFET或IGBT驅動器IR2101采用高度集成的電平轉換技術，同時上管采用外部自舉電容上電，能夠穩定高效地驅動MOS管。該逆變器可以實現dc/AC的轉換，最大功率點的跟蹤等功能。實際測試結果表明，該逆變器系統具有跟蹤能力強，穩定性高，反應靈敏等特點，該逆變器不僅可應用于普通的電源逆變系統，而且可應用于光伏并網發電的逆變系統，具有廣泛的市場前景。 Abstract: To solve the problem of dc-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as dc/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上傳時間： 2013-11-17
上傳用戶：lliuhhui
鎖定放大是微弱信號檢測的重要手段?；谙嚓P檢測理論，利用開關電容的開關實現鎖定放大器中乘法器的功能，提出開關電容和積分器相結合以實現相關檢測的方法，并設計出一種鎖定放大器。該鎖定放大器將微弱信號轉化為與之相關的方波，通過后續電路得到正比于被測信號的直流電平，為后續采集處理提供方便。測量數據表明鎖定放大器前級可將10-6 A的電流轉換為10-1 V的電壓，后級通過帶通濾波器級聯可將信號放大1×105倍。該方法在降低噪聲的同時，可對微弱信號進行放大，線性度較高、穩定性較好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then dc proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上傳時間： 2013-11-29
上傳用戶：黑漆漆
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上傳時間： 2013-10-10
上傳用戶：1184599859
XRP7714是一款四輸出脈寬調制（PWM）分級降壓（step down）dc-dc控制器，并具有內置LDO提供待機電源。該器件在單個IC上為電池供電的產品提供了整套的電源管理方案，并且通過內含的I2C串行接口進行整體的編程配置。XRP7714器件的每一路輸出電壓的編程范圍是0.9V～5.1V，此范圍內無需外部分壓器?？删幊藾PWM開關頻率的范圍從300kHz到1.5MHz，使用戶能夠在效率和元件大小之間取得最優方案。為了讓用戶能夠在設計的多路電源XRP7714系統能夠取得最優的方案，下文將詳細的介紹影響XRP7714系統效率的參數設置以及外圍器件的選型。
上傳時間： 2013-10-31
上傳用戶：chendawei
