The 87LPC76X Microcontroller combines in a small package thebenefits of a high-performance microcontroller with on-boardhardware supporting the Inter-Integrated Circuit (I2C) bus interface.The 87LPC76X can be programmed both as an I2C bus master, aslave, or both. An overview of the I2C bus and description of the bussupport hardware in the 87LPC76X microcontrollers appears inapplication note AN464, Using the 87LPC76X Microcontroller as anI2C Bus Master. That application note includes a programmingexample, demonstrating a bus-master code. Here we show anexample of programming the microcontroller as an I2C slave.The code listing demonstrates communications routines for the87LPC76X as a slave on the I2C bus. It compliments the program inAN464 which demonstrates the 87LPC76X as an I2C bus master.One may demonstrate two 87LPC76X devices communicating witheach other on the I2C bus, using the AN464 code in one, and theprogram presented here in the other. The examples presented hereand in AN464 allow the 87LPC76X to be either a master or a slave,but not both. Switching between master and slave roles in amultimaster environment is described in application note AN435.The software for a slave on the bus is relatively simple, as theprocessor plays a relatively passive role. It does not initiate bustransfers on its own, but responds to a master initiating thecommunications. This is true whether the slave receives or transmitsdata—transmission takes place only as a response to a busmaster’s request. The slave does not have to worry about arbitrationor about devices which do not acknowledge their address. As theslave is not supposed to take control of the bus, we do not demandit to resolve bus exceptions or “hangups”. If the bus becomesinactive the processor simply withdraws, not interfering with themaster (or masters) on the bus which should (hopefully) try toresolve the situation.
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
The XPS Ethernetlite peripheral does not provide any mechanism to access the Ethernet PHYregisters. These registers are used to configure auto negotiation parameters and to obtain PHYstatus. This application note provides reference systems and associated software to accessPHY registers by connecting the serial management bus signals MDC and MDIO to GPIOswhich the software controls directly.
The PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
Most designers wish to utilize as much of a device as possible in order to enhance the overallproduct performance, or extend a feature set. As a design grows, inevitably it will exceed thearchitectural limitations of the device. Exactly why a design does not fit can sometimes bedifficult to determine. Programmable logic devices can be configured in almost an infinitenumber of ways. The same design may fit when you use certain implementation switches, andfail to fit when using other switches. This application note attempts to clarify the CPLD softwareimplementation (CPLDFit) options, as well as discuss implementation tips in CoolRunnerTM-IIdesigns in order to maximize CPLD utilization.
Addfilter is a command-line application which adds and removes filter drivers for a given drive or volume. It is intended to demonstrate how to insert a filter driver into the driver stack of a device. The sample illustrates how to do this by using the SetupDi APIs. The sample works on both x86 and Alpha platforms. It has only been tested in a 32-bit environment. Since Addfilter is not a driver, it does not deal with Plug and Play or Power Management.
Client/Server版本 DBISAM compiles directly into your application with no external libraries required. Runtime package support is also provided if so desired. It has a very small footprint and does not require any forms support in Delphi 6, C++Builder 6, and Kylix 2 and higher, which helps keep the size of non-UI applications like services or web applications to a minimum.
builds an alternate memory allocation scheme into ToyFDTD1. Contributed by John Schneider, it guarantees that the data arrays are contiguous, which the ToyFDTD1 scheme does not. Released 6 December, 1999.
