The voltage range of Linear Technology’s PowerPath® circuitscan be easily extended with just a few components, thusallowing them to meet the needs of virtually all applications.This application note presents solutions for circuits thatmust withstand large negative voltages, a reverse adapterinput for example, and circuits that must withstand largepositive inputs, such as automotive load-dump.
為解決電致變色器件的顏色變化受外界環境顏色控制的問題，設計了一種基于單片機的便攜式顏色自適應識別電路。與傳統顏色識別電路相比較，該電路利用數字式的顏色傳感器來獲取外界環境顏色，產生的數字顏色信號易于單片機進行處理。在電路中，下位機部分主要負責獲取電致變色器件變色參數及控制電致變色器件的顏色變化;而上位機部分主要負責把下位機獲取的電致變色器件變色參數進行電壓到顏色的曲線擬合，并通過藍牙通信把擬合曲線參數傳遞給下位機。結果表明，該電路能自動根據環境顏色提供-4~4 V范圍步進為0.1 V的電壓來驅動電致變色器件的顏色顯示，與傳統的顏色識別電路設計相比，識別的精度和速度都得到了明顯改善。
Abstract:
In this paper， a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit， the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data， which can be processed easily by MCU. In PACCI， the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic device and further driving it. For the master， which is mainly responsible for the color curve fitting based on the parameters of the electrochromic device， and transmits the fitting parameters to the slave through the bluetooth device. The results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic device. Compared to the traditional color recognition circuit， the recognition accuracy and speed of PACCI have been improved significantly.
介紹了基于單片機航空交流電參數測試儀的系統設計。以Silicon Labs公司的C8051F005單片機為核心設計出數據采集板，通過RS-232串口與上位機通訊。運用Lab Windows/CVI編寫的上位機軟件實現信號的檢測以及波形和數據的顯示，給出了測試儀硬件電路的組成和軟件流程圖。本系統具有硬件結構簡單、容易實現和成本低等特點，在實際應用中其穩定性、精確性均能滿足客戶要求。
Abstract:
The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
Abstract: This application note explains the hardware of different types of 1-Wire® interfaces and software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project and the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface and 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface.
There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet individual needs.
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
SRAM-based FPGAs are non-volatile devices. Upon powerup, They are required to be programmed from an external source. This procedure allows anyone to easily monitor the bit-stream, and clone the device. The problem then becomes how can you effectively protect your intellectual property from others in an architecture where the part is externally programmed?
UART 4 UART參考設計，Xilinx提供VHDL代碼 uart_vhdl
This zip file contains the following folders:
\vhdl_source -- Source VHDL files:
uart.vhd - top level file
txmit.vhd - transmit portion of uart
rcvr.vhd - - receive portion of uart
\vhdl_testfixture -- VHDL Testbench files. This files only include the testbench behavior, they
do not instantiate the DUT. This can easily be done in a top-level VHDL
file or a schematic. This folder contains the following files:
txmit_tb.vhd -- Test bench for txmit.vhd.
rcvr_tf.vhd -- Test bench for rcvr.vhd.
The CC1101 is a low-cost sub- 1 GHztransceiver designed for very low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
