The fundamental problem of communication is that of reproducing at one point either exactly or approximately a message selected at another point. Frequently the messages have meaning; that is they refer to or are correlated according to some system with certain physical or conceptual entities.
USB接口控制器參考設計,xilinx提供VHDL代碼 usb xilinx vhdl
; This program is free software; you can redistribute it and/or modify
; it under the terms of the GNU General Public License as published by
; the Free Software Foundation; either version 2 of the License, or
; (at your option) any later version.
;
; This program is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with this program; if not, write to the Free Software
; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
本軟件是關于MAX338, MAX339的英文數據手冊：MAX338, MAX339 8通道/雙4通道、低泄漏、CMOS模擬多路復用器
The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions.
These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
使用Nios II軟件構建工具
This chapter describes the Nios® II Software Build Tools (SBT), a set of utilities and
scripts that creates and builds embedded C/C++ application projects, user library
projects, and board support packages (BSPs). The Nios II SBT supports a repeatable,
scriptable, and archivable process for creating your software product.
You can invoke the Nios II SBT through either of the following user interfaces:
■ The Eclipse™ GUI
■ The Nios II Command Shell
The purpose of this chapter is to make you familiar with the internal functionality of
the Nios II SBT, independent of the user interface employed.
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
XAPP520將符合2.5V和3.3V I/O標準的7系列FPGA高性能I/O Bank進行連接
The I/Os in Xilinx® 7 series FPGAs are classified as either high range (HR) or high performance (HP) banks. HR I/O banks can be operated from 1.2V to 3.3V, whereas HP I/O banks are optimized for operation between 1.2V and 1.8V. In circumstances that require an HP 1.8V I/O bank to interface with 2.5V or 3.3V logic, a range of options can be deployed. This application note describes methodologies for interfacing 7 series HP I/O banks with 2.5V and 3.3V systems
This document was developed under the Standard Hardware and Reliability Program (SHARP) TechnologyIndependent Representation of Electronic Products (TIREP) project. It is intended for use by VHSIC HardwareDescription Language (VHDL) design engineers and is offered as guidance for the development of VHDL modelswhich are compliant with the VHDL Data Item Description (DID DI-EGDS-80811) and which can be providedto manufacturing engineering personnel for the development of production data and the subsequent productionof hardware. Most VHDL modeling performed to date has been concentrated at either the component level orat the conceptual system level. The assembly and sub-assembly levels have been largely disregarded. Under theSHARP TIREP project, an attempt has been made to help close this gap. The TIREP models are based upon lowcomplexity Standard Electronic Modules (SEM) of the format A configuration. Although these modules are quitesimple, it is felt that the lessons learned offer guidance which can readily be applied to a wide range of assemblytypes and complexities.
The fundamental problem of communication is that of reproducing at one point either exactly or approximately a message selected at another point. Frequently the messages have meaning; that is they refer to or are correlated according to some system with certain physical or conceptual entities.
One of the strengths of Synplify is the Finite State Machine compiler. This is a powerfulfeature that not only has the ability to automatically detect state machines in the sourcecode, and implement them with either sequential, gray, or one-hot encoding. But alsoperform a reachability analysis to determine all the states that could possibly bereached, and optimize away all states and transition logic that can not be reached.Thus, producing a highly optimal final implementation of the state machine.
