This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded Evaluation Kit, Cyclone III edition (NEEK).
標簽： SOPC controller component SPI-mode
上傳時間： 2017-05-14
上傳用戶：LouieWu
This book introduces embedded systems to C and C++ programmers. Topics include testing memory devices, writing and erasing Flash memory, verifying nonvolatile memory contents, controlling on-chip peripherals, device driver design and implementation, optimizing embedded code for size and speed, and making the most of C++ without a performance penalty.
標簽： programmers introduces embedded include
上傳時間： 2013-12-21
上傳用戶：daoxiang126
This is schematic and Gerber files of PCB that is used for GSM alarm system. This is industrial-grade system with many features like 1-wire (iButton) interface, additional interface for video camera (UART JPEG camera is used), SD card to store pictures from camera and send them by GSM to remote mobile phone. Can be used as a reference design for anyone who wants to make own GSM alarm system system based on SIM300C module from Simcom.
標簽： This industrial-grad schematic is
上傳時間： 2013-12-06
上傳用戶：com1com2
Altera® provides various tools for development of hardware and software for embedded systems. This handbook complements the primary documentation for these tools by describing how to most effectively use the tools. It recommends design styles and practices for developing, debugging, and optimizing embedded systems using Altera-provided tools. The handbook introduces concepts to new users of Altera’s embedded solutions, and helps to increase the design efficiency of the experienced user.
標簽： development for provides embedded
上傳時間： 2017-06-15
上傳用戶：haoxiyizhong
High volume USB 2.0 devices will be designed using ASIC technology with embedded USB 2.0 support. For full-speed USB devices the operating frequency was low enough to allow data recovery to be handled in a vendors VHDL code, with the ASIC vendor providing only a simple level translator to meet the USB signaling requirements. Today s gate arrays operate comfortably between 30 and 60 MHz. With USB 2.0 signaling running at hundreds of MHz, the existing design methodology must change.
標簽： technology 2.0 USB designed
上傳時間： 2014-01-02
上傳用戶：二驅蚊器
High volume USB 2.0 devices will be designed using ASIC technology with embedded USB 2.0 support. For full-speed USB devices the operating frequency was low enough to allow data recovery to be handled in a vendors VHDL code, with the ASIC vendor providing only a simple level translator to meet the USB signaling requirements. Today s gate arrays operate comfortably between 30 and 60 MHz. With USB 2.0 signaling running at hundreds of MHz, the existing design methodology must change.
標簽： technology 2.0 USB designed
上傳時間： 2017-07-05
上傳用戶：zhoujunzhen
ARM System Developer s Guide: Designing and Optimizing System Software (The Morgan Kaufmann Series in Computer Architecture and Design)
標簽： System Optimizing Developer Designing
上傳時間： 2014-01-12
上傳用戶：gundan
This software is developed to provide ease with controller design. For PID control, options are given to design and analyse the compensated and uncompensated system. You are free to choice among Proportional PI, PD and PID mode of control. Both frequency and time domain characteristics can be observed. Special Menus are given to observe time and frequency response plots. For Statefeedback controller similar options are given. But this is limited to second order system only.
標簽： controller developed software control
上傳時間： 2017-07-25
上傳用戶：aysyzxzm
Introduction to the RTX51, a multitasking real-time operating system for the 8051 family. RTX51 simplifies system and software design of complex and time-critical projects.
標簽： Introduction multitasking the RTX
上傳時間： 2017-08-01
上傳用戶：liansi
Componentized, real-time operating system and powerful tools for building a broad range of small-footprint embedded solutions
標簽： Componentized real-time operating building
上傳時間： 2017-08-15
上傳用戶：三人用菜
<button id="ycmom"></button>