A complete design for a data acquisition card for the IBM PC is detailed in this application note. Additionally, C language code is provided to allow sampling of data at speed of more than 20kHz. The speed limitation is strictly based on the execution speed of the "C" data acquisition loop. A "Turbo" XT can acquire data at speeds greater than 20kHz. Machines with 80286 and 80386 processors can go faster than 20kHz. The computer that was used as a test bed in this application was an XT running at 4.77MHz and therefore all system timing and acquisition time measurements are based on a 4.77MHz clock speed.
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty.
With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
MAXQUSBJTAGOW評估板軟件:關鍵特性 Easily Load and Debug Code Interface Provides In-Application Debugging Features Step-by-Step execution Tracing Breakpointing by Code Address, Data Memory Address, or Register Access Data Memory View and Edit Supports Logic Levels from 1.1V to 3.6V Supports JTAG and 1-Wire Protocols Each Adapter Has Its Own Unique Serial ID, Allowing Multiple Adapters to be Connected Without COM Port Conflicts Has In-Field Upgradable Capability if Firmware Needs to be Upgraded Enclosure Protects from Shorts and ESD
MAXQUSBJTAGOW評估板軟件:關鍵特性 Easily Load and Debug Code Interface Provides In-Application Debugging Features Step-by-Step execution Tracing Breakpointing by Code Address, Data Memory Address, or Register Access Data Memory View and Edit Supports Logic Levels from 1.1V to 3.6V Supports JTAG and 1-Wire Protocols Each Adapter Has Its Own Unique Serial ID, Allowing Multiple Adapters to be Connected Without COM Port Conflicts Has In-Field Upgradable Capability if Firmware Needs to be Upgraded Enclosure Protects from Shorts and ESD
This code detects memory leaks in embedded VC++ almost the same way crtdbg does in VC++. At the end of program execution it will display in the debug window if there were any memory leaks and how the memory looks so you can identify where your memory leak occurred. It will display in the debug window a message saying no memory leaks detected if there are no memory leaks. Similar to what crtdbg.h does in VC++. The code detects memory leaks generated with calls to new and delete operators in C++. The code doesn t detect memory leaks generated with C functions: malloc, calloc, free, but that can be done in the future. Let me know and I will program it.
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file.
• Assume a file with correct data (no garbage, characters, etc.).
• you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour:
o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the
next size for the next 2 matrices (if not end of file).
o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and
discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
This prj demonstrates how to use the SROM memory classes for the Dallas DS80C400. This example uses the memcpy function to copy a function in the SROM memory class (which is located in CODE memory) to von Neumann mapped XDATA (starting at 0x110000) for execution.
This thorough, hands-on reference for database developers and administrators delivers expert guidance on sophisticated uses of Transact-SQL (T-SQL)¡ ª one of the most familiar and powerful programming languages for SQL Server. Written by a T-SQL guru, this guide focuses on language features and how they are interpreted and processed by the SQL Server execution engine. You¡ ¯ ll get in-depth coverage of the sophisticated uses of T-SQL, including triggers, user-defined functions, exception handling, and more. The book explains and compares solutions to database-development problems in both SQL Server 2000 and SQL Server 2005, discussing the new T-SQL programming features added to SQL Server 2005 in detail. Includes extensive code samples, table examples, and logic puzzles to help database developers and administrators understand the intricacies and help promote mastery of T-SQL.
This Source.zip has three application code folders containing .java and .class files and two .jar files as follows:
1. desktop-side_JXTA4JMS
2. mobile-side_JXTA4JMS
3. JMS Test Client
4. Listener.jar
5. JMSTestClient.jar
We now explain execution steps, we followed, to run this JXTA4JMS application.
Before we try we require Application softwares and need to configure JXTA relay and J2EE server.
