The two C source files in this archive are specific to the TRS-80 Model 4 with
high-resolution graphics board. However, the code which performs Huffman enco-
ding and decoding is of general interest.
The two C source files in this archive are specific to the TRS-80 Model 4 with
high-resolution graphics board. However, the code which performs Huffman enco-
ding and decoding is of general interest.
This application note describes a Linear Technology "Half-Flash" A/D converter, the LTC1099, being connected to a 256 element line scan photodiode array. This technology adapts itself to handheld (i.e., low power) bar code readers, as well as high resolution automated machine inspection applications..
The makers of handheld medical, industrial and consumerdevices use a wide variety of high resolution, small tomedium sized color TFT LCD displays. The power supplydesigners for these displays must contend with shrinkingboard area, tight schedules, and variations in displaytypes and feature requirements. The LTC®3524 simplifi esthe designer’s job by combining a versatile, easily programmed,TFT LCD bias supply and white LED backlightdriver in a low profi le 4mm × 4mm QFN package.
為了使音頻信號分析儀小巧可靠，成本低廉，設計了以2片MSP430F1611單片機為核心的系統。該系統將音頻信號送入八階巴特沃茲低通濾波器，對信號進行限幅放大、衰減、電平位移、緩沖，并利用一單片機負責對前級處理后的模擬信號進行采樣，將采集得到的音頻信號進行4 096點基2的FFT計算，并對信號加窗函數提高分辨率，另一單片機負責對信號的分析及控制顯示設備。此設計精確的測量了音頻信號的功率譜、周期性、失真度指標，達到較高的頻率分辨率，并能將測量結果通過紅外遙控器顯示在液晶屏上。
Abstract:
o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
This application note discusses a variety of approaches for interfacing analog signals to 5V powered systems. Synthesizing a "rail-to-rail" op amp and scaling techniques for A/D converters are covered. A voltage-to-frequency converter, applicable where high resolution is required, is also presented.
The objective is to set up SPI communication between VTI Technologies digital pressure sensor
component and an MCU of an application device ATMEGA16L. In this code example:
?The MCU is configured
?SCP1000-D01 is initialized and configured
?The high resolution measurement mode is activated
?Temperature and pressure information is read always when the DRDY pin is in high state
Please refer to the document "SCP1000 Product Family Specification 8260800" for further
information on SCP1000 register addressing and SPI communication. This document applies to the
SCP1000-D01.
The FPGA can realize a more optimized Digital controller in DC/DC Converters when compare to DSPs. In this paper, based on the FPGA platform, The theoretical analysis, characteristics, simulation and design consideration are given. The methods to implement the digital DC/DC Converters have been researched. The function module, state machine of digital DC/DC controller and high resolution DPWM with Sigma-
Delta dither has been introduced. They are verified by experiments on a 20 W, 300 KHz non-isolated synchronous buck converters.
