<pre id="gsucc"></pre> Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上傳時間： 2013-11-23
上傳用戶：新手無憂
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上傳時間： 2013-11-07
上傳用戶：moerwang
The LTC®4151 is a high side power monitor that includesa 12-bit ADC for measuring current and voltage, as wellas the voltage on an auxiliary input. Data is read throughthe widely used I2C interface. An unusual feature in thisdevice is its 7V to 80V operating range, allowing it to coverapplications from 12V automotive to 48V telecom.
上傳時間： 2013-10-29
上傳用戶：集美慧
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上傳時間： 2013-10-31
上傳用戶：wwwe
Handheld electronic devices play a key role in our everydaylives. Because dependability is paramount, handhelds arecarefully engineered with lightweight power sources forreliable use under normal conditions. But no amount ofcareful engineering can prevent the mistreatment theywill undergo at the hands of humans. For example, whathappens when a factory worker drops a bar code scanner,causing the battery to pop out? Such events areelectronically unpredictable, and important data storedin volatile memory would be lost without some form ofsafety net—namely a short-term power holdup systemthat stores suffi cient energy to supply standby power untilthe battery can be replaced or the data can be stored inpermanent memory.
上傳時間： 2013-11-05
上傳用戶：coeus
What would happen if someone connected 24V to your12V circuits? If the power and ground lines were inadvertentlyreversed, would the circuits survive? Does yourapplication reside in a harsh environment, where the inputsupply can ring very high or even below ground? Evenif these events are unlikely, it only takes one to destroya circuit board.
上傳時間： 2013-10-26
上傳用戶：jackandlee
AN22 details the theoretical and application aspects of the LT1088 thermal RMS/DC converter. The basic theory behind thermal RMS/DC conversion is discussed and design details of the LT1088 are presented. Circuitry for RMS/DC converters, wideband input buffers and heater protection is shown.
上傳時間： 2013-10-16
上傳用戶：china97wan
In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveelements or both. Additionally, to conserve power,particularly in battery driven apparatus such as cellulartelephones, the regulators must operate with low input-tooutputvoltages.1 Devices presently becoming availablemeet these requirements (see separate section, “A Familyof 20mVRMS Noise, Low Dropout Regulators”).
上傳時間： 2013-10-30
上傳用戶：yeling1919
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上傳時間： 2014-01-18
上傳用戶：laomv123
為了改變目前電網現場作業管理的變電巡檢、變電檢修試驗、輸電線路巡檢檢修等管理系統各自獨立運行，信息不能共享，功能、效率受限，建設和維護成本高的現狀，提出了采用B/S+C/S構架模式，將各現場作業管理模塊和生產MIS（管理系統）集成為一體的現場作業管理系統的設計方案，做到各子系統和生產MIS軟硬資源共享，做到同一數據唯一入口、一處錄入多處使用。各子系統設備人員等基礎信息來源于生產管理系統，各子系統又是生產管理系統的作業數據、缺陷信息的重要來源。經過研究試用成功和推廣應用，目前該系統已在江西電網220 kV及以上變電站全面應用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上傳時間： 2013-11-15
上傳用戶：han_zh
