對某四輪獨立驅動電動汽車輪轂電機進行研究,設計一種永磁無刷直流電機控制器.以STM32F103RBT6芯片為基礎,對電機驅動電路、采樣電路和保護電路分別進行硬件設計與分析;同時,采用模塊化軟件設計方案,對該控制器的軟件系統進行升級.實驗驗證表明:所設計的電機控制器能使電機響應迅速、轉速穩定、無超調,且電動車動力輸出性能良好.A permanent magnet brushless direct current motor controller was designed by studying the hub motor of a four-wheel independent drive electric vehicle.Based on STM32 F103RBT6 chip,the hardware design and analysis of motor drive circuit,sampling circuit and protection circuit were carried out respectively.At the same time,modular software design scheme was adopted to upgrade the software system of the controller.Experimental results show that the designed motor controller can ensure the motor fast response,stable speed,no overshoot,and good power output performances.
LED 線陣顯示裝置, 分為 LED 線性旋轉顯示主機和圖文錄入器兩部分。主機用直流電機帶動由紅綠 LED 組成的線陣旋轉, 同時線陣按照時序依次切換顯示狀態, 在固定區域利用視覺暫留效果形成 16×16 點陣, 用以顯示圖文;圖文錄入器用 HMI 觸控屏作為人機交互界面, 實現圖文錄入和回放功能。主機與圖文錄入器通過無線通信方式進行信息交互,可由圖文錄入器控制主機切換不同工作任務, 以及改變線陣顯示內容。The LED linear array display device is divided into two parts:the one is the main unit used to display content,and the other one is used to input the contents.The main unit is driven by a DC motor to rotate the linear array composed by red and green light emitting diodes.At the same time,the 16×16 dot matrix that switching the display state according to the time sequence on the main unit displays pictures and texts in the fixed area,by using the visual temporary effect.The HMI touch screen is used as human machine interface to realize the function that input and playback pictures and texts.The two parts of the device communicate with each other through wireless communication.The image and text input controller can control the main unit to switch different tasks and change the content of linear array displayed.
近距電能傳輸——高效安全近距電能傳輸一般基于電磁感應原理進行。在此技術基礎上，當接收器鄰近發射器時才會進行電能傳輸。電磁感應技術的歷史長達百年，多年米一直應用于各類電子產品中—如此普及全因其簡單、高效以及安全技術概覽以下將為你簡要介紹無線電能傳輸技術。System Overview(Communication)Receiver sends messagesTo provide control information to the transmitterBy load modulation on the power signaTransmitter receives messagesTo receive control information frorn the recelverBy de-modulation of the reflected loadPower Pick Up( Receiver)Secondary coil (L Serial resonance capacitor (C) for efficient power transfer Parallel resonance capacitor(C, )for detection purposes Rectifier: full bridge(diode, or switched)+ capacitor Output switch for(dis)connecting the loadReceiver modulates load by Switching modulation resistor(R,n),or Switching modulation capacitor(Ca)Transmitter de-modulates reflected load by Sensing pnmary coil curent (p)and/o Sensing primary coil voltage (V,
介紹一種萬能模擬信號輸入采集電路,可以同時支持電壓、電流、熱電偶、熱電阻等常見的工業類型信號,方便后級電路的測量。該研究成果通過不斷優化和完善,已成功應用到了中控儀表的新產品中。The paper introduces a collection circuit of universal signal input. The circuit support voltage, current, thermocouple, thermal resistance and other common industrial type signal. The research results, which has been continuous optimized and improved, has been successfully applied to the new production of Zhejiang Supcon Instrument Co., Ltd.
基于PSIM仿真軟件，分析了Boost電路拓撲結構，設定了參數要求進行電路仿真設計，通過電路仿真軟件PSIM對Boost電路工作在CCM模式下，合理設置占空比參數。實驗結果表明理論分析與仿真的一致性和參數設計的正確性，輸出電壓和電流參數穩定，Boost電路輸出效率高。This design is based on PSIM simulation software,analyzes the topology of Boost circuit,sets the parameter re- quirements for circuit simulation design,and reasonably sets the duty cycle parameters for Boost circuit working in CCM mode through PSIM simulation software.The experimental results show that the theoretical analysis and simulation are consis- tent and the parameter design is correct,the output voltage and current parameters are stable.
The JW? 7805 is a low noise low-dropout (LDO) voltage regulator with enable function that operates from 1.8V to 5.5V. It provides up to 300mA of output current and offers low-power operation in miniaturized packaging. JW7805 supports fixed output voltage 0.9V, 1.0V, 1.05V, 1.1V,1.2V, 1.3V, 1.35V, 1.5V, 1.8V, 1.85V, 2.1V, 2.2V, 2.3V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V,3.1V, 3.3V, 3.6V, 4.2V, 4.4V and 5.0V. The features of low quiescent current as low as 6uA and almost zero disable current are ideal for powering the battery equipment. JW7805’s low output noise and high PSRR are also friendly to RF systems.
數字頻率計是電工電子中常用的測量儀器,數字頻率計通過用輸入待測信號對一特定長度的信號進行計數,從而得出頻率并通過數碼管直觀的顯示出來。本文提出了一種與輸入同步的數字頻率計的設計,提高了頻率計的精度,設計采用Multisim軟件進行設計和仿真的過程,介紹了其工作原理,硬件電路設計和仿真的過程。設計采用了Multisim軟件進行設計和仿真,設計結果得到的驗證。Digital frequency counter is used to measure the frequency of a signal.It is common to use a multivibrator to generate a standard 1 second time base signal and count input signal gated by this signal.However,the asynchronous of this time base signal with input signal will bring errors.In this paper,a high precision frequency counter which use synchronized time base signal generator is proposed.This frequency counter is designed and simulated by Multisim tools and result is verified.
RX-8801 SA Features built-in 32.768 kHz DTCXO, High Stability Supports l'C-Bus's high speed mode (400 kHz)Alarm interrupt function for day, date, hour, and minute settings Fixed-cycle timer interrupt function Time update interrupt function32.768 kHz output with OE function Auto correction of leap years Wide interface voltage range: 2.2 V to 5.5 V Wide time-keeping voltage range:1.8 V to 5.5 V Low current consumption: 0.84A/3V (Typ.)is an IC bus interface-compliant real-time clock which includes a 32.768 kHz DTCXO In addition to providing a calendar (year, month, date, day, hour, minute, second) function and a clock counter function, this module provides an abundance of other functions including an alarm function, fixed-cycle timer unction, time update interrupt function, and 32.768 kHz output function.The devices in this module are fabricated via a C-MOS process for low current consumption, which enables ong-term battery back-up.
INTRODUCTION In the past, adding speech recording and playback capability to a product meant using a digital signal processor or a specialized audio chip. Now, using a simplified Adaptive Differential Pulse Code Modulation(ADPCM) algorithm, these audio capabilities can be added to any PICmicro device. This application note will cover the ADPCM compression and decompression algorithms, performance comparison of all PICmicro devices, and an application using a PIC16C72 micro-controller.DEFINITION OF TERMS step size -value of the step used for quantization of ana-log signals and inverse quantization of a number of steps.quantization -the digital form of an analog input signal is represented by a finite number of steps.adaptive quantization -the step size of a quantizer is dramatically changed with time in order to adapt to a changing input signal.inverse quantizer -a finite number of steps is converted into a digital representation of an analog signal.
Introduction The Sil9135/Sil9135A HDMI Receiver with Enhanced Audio and Deep Color Outputs is a second-generation dual-input High Definition Multimedia Interface(HDMI)receiver. It is software-compatible with the Sil9133receiver, but adds audio support for DTS-HD and Dolby TrueHD. Digital televisions that can display 10-or 12-bit color depth can now provide the highest quality protected digital audio and video over a single cable. The Sil9135and Sil9135A devices, which are functionally identical, can receive Deep Color video up to 12-bit,1080p @60Hz. Backward compatibility with the DVI 1.0specification allows HDMI systems to connect to existing DVI 1.0 hosts, such as HD set-top boxes and PCs. Silicon Image HDMI receivers use the latest generation Transition Minimized Differential Signaling(TMDS) core technology that runs at 25-225 MHz.The chip comes pre-programmed with High-bandwidth?
