Photomultipliers (PMT), avalanche photodiodes (APD),ultrasonic transducers, capacitance microphones, radiationdetectors and similar devices require high voltage,low current bias. Additionally, the high voltage must bepristinely free of noise; well under a millivolt is a commonrequirement with a few hundred microvolts sometimesnecessary. Normally, switching regulator confi gurationscannot achieve this performance level without employingspecial techniques. One aid to achieving low noise is thatload currents rarely exceed 5mA. This freedom permitsoutput fi ltering methods that are usually impractical
In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveelements or both. Additionally, to conserve power,particularly in battery driven apparatus such as cellulartelephones, the regulators must operate with low input-tooutputvoltages.1 Devices presently becoming availablemeet these requirements (see separate section, “A Familyof 20mVRMS Noise, Low Dropout Regulators”).
The above title is not happenstance and was arrived at afterconsiderable deliberation. As a linear IC manufacturer, it isour goal to encourage users to design and build switchingregulators. A problem is that while everyone agrees thatworking switching regulators are a good thing, everyonealso agrees that they are difficult to get working. Switchingregulators, with their high efficiency and small size, areincreasingly desirable as overall package sizes shrink.Unfortunately, switching regulators are also one of themost difficult linear circuits to design. Mysterious modes,sudden, seemingly inexplicable failures, peculiar regulationcharacteristics and just plain explosions are commonoccurrences. Diodes conduct the wrong way. Things gethot that shouldn’t. Capacitors act like resistors, fusesdon’t blow and transistors do. The output is at ground, andthe ground terminal shows volts of noise.
鎖定放大是微弱信號檢測的重要手段。基于相關檢測理論，利用開關電容的開關實現鎖定放大器中乘法器的功能，提出開關電容和積分器相結合以實現相關檢測的方法，并設計出一種鎖定放大器。該鎖定放大器將微弱信號轉化為與之相關的方波，通過后續電路得到正比于被測信號的直流電平，為后續采集處理提供方便。測量數據表明鎖定放大器前級可將10-6 A的電流轉換為10-1 V的電壓，后級通過帶通濾波器級聯可將信號放大1×105倍。該方法在降低噪聲的同時，可對微弱信號進行放大，線性度較高、穩定性較好。
Abstract:
Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
畢業設計 USB TO Gigabit LAN 網卡 隨著網絡技術飛速發展，多媒體的應用越來越多，人們對網絡的要求也越來越高，為了適應市場的需求，網卡出現了。它以其結構簡單、成本低廉、兼容性強等諸多的優越性得到了廣泛的應用。由于網絡的應用越來越廣泛，網卡的應用也越來越多、功能越來越強大。開始時由于技術方面的限制，網卡只有10Mbps的吞吐量，由于網絡技術的發展，100Mbps吞吐量的網卡開始在市場上得到廣泛的應用。而現在1000Mbps吞吐量的網卡的出現又給網絡的傳輸帶來了新的活力。 論文中主要闡述了基于以太網的USB TO Gigabit LAN網卡的設計與制作。論文首先對以太網進行了介紹，緊接著講了網卡的基本知識。隨后又對USB TO Gigabit LAN網卡的電路設計和制作進行了詳細的描述。論文還包括了USB TO Gigabit LAN網卡的調試等內容。
This white paper raises some fundamental issues the design engineer should address before deciding upon a communication approach for a wireless network. As no universal wireless network solution exists, it should be custom tailored to suit the application demands. Defining your application communication characteristics is the key to ensure optimal communication reliability and resistance to interfering noise sources.
在理論分析循環碼編碼和譯碼基本原理的基礎上，提出了基于單片機系統的(24，16)循環碼軟件實現編碼、譯碼的方案。仿真結果表明(24，16)循環碼能有效地克服來自通訊信道的干擾，保證數據通信的可靠及系統的穩定，使誤碼率大幅度降低。本論文對(24，16)循環碼的研究結果表明，可以有效地降低錯誤概率和提高系統的吞吐量，實現糾錯僅需要在接收端增加有限的存儲空間和計算復雜度，具有一定的實用價值。
Abstract:
Based on analyzing the theory of encoding and decoding of cyclic code， this paper showed the schemes of encoding and decoding of(24，16)cyclic code by the software and based on microcontroller. Simulation results show that using (24，16) cyclic codes can effectively overcome the interference from communication channel， ensure the reliability and stability of data communication systems， and reduce the bit error rate greatly. The results of this paper show that by using the (24，16) cyclic code， the error rate can be reduced and the system throughput can be improved. Meanwhile， the system only needs to enlarge limited storage space and computation the complexity at the receiving end to realize error correction. Thus the (24，16) cyclic code has a practical value.
針對盤山路存在的轉彎盲區，即在轉彎時司機無法得知彎路對面是否有車輛通過，設計一種基于C8051F310的山路轉彎預防警示系統。該系統利用一階濾波算法檢測山路轉彎時是否有車輛通過。運用該算法可增強系統檢測的實時性，提高檢測機動車輛的靈敏度，同時大大減少環境溫度對檢測的干擾。試驗表明該系統能夠正確指示出在山路轉彎時是否有車輛通過，目前該系統已安裝在盤山路上，可大大減少事故的發生率。
Abstract:
Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。
Abstract:
A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
