Automobile electronic systems place high demands ontoday’s DC/DC converters. They must be able to preciselyregulate an output voltage in the face of wide temperatureand input voltage ranges—including load dump transientsin excess of 60V and cold crank voltage drops to 4V. Theconverter must also be able to minimize battery drain inalways-on systems by maintaining high effi ciency over abroad load current range. Similar demands are made bymany 48V nonisolated telecom applications, 40V FireWireperipherals and battery-powered applications with autoplug adaptors. The LT3437’s best in classperformancemeets all of these requirements in a small thermallyenhanced 3mm × 3mm DFN package.
上傳時間： 2013-10-15
上傳用戶：stampede
Switching regulators are of universal interest. LinearTechnology has made a major effort to address this topic.A catalog of circuits has been compiled so that a designengineer can swiftly determine which converter type isbest. This catalog serves as a visual index to be browsedthrough for a specific or general interest.
標簽： Collection Switching Regulator Circuit
上傳時間： 2013-11-09
上傳用戶：mh_zhaohy
Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
標簽： 數字電源
上傳時間： 2013-10-16
上傳用戶：dddddd
the first drawing i have made PCB in my college,which was downloade from NET
上傳時間： 2013-10-20
上傳用戶：shenlan
Designing Boards with Atmel AT89C51,AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test. Recent improvements in chips and testers have made it possible for the tester to begin taking over the role tradi-tionally assigned to the PROM program-mer. Instead of having a PROM pro- grammer write nonvolatile memories before assembling the board, the in-cir- cuit tester writes them during in-circuit testing operations. Many Teradyne Z18- series testers are now in use loading code into nonvolatile memories, micro- controllers and in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s, so that designers of boards using these chips can get the best results.
上傳時間： 2013-11-17
上傳用戶：xiaozhiqban
為了有效地提升鉛酸蓄電池的使用壽命，同時實現對充電過程的監控，設計出一種用單片機控制的36 V鉛酸蓄電池充電電源。本電路采用反激式拓撲，連續電流工作模式，電源管理IC設計在電源的副邊，由ELAN公司的EM78P258N單片機模擬，是用可編程器件模擬電源管理IC，實現智能電源低成本化的一次成功嘗試，通過對單片機的軟件設計實現了充電電源的狀態顯示、充電時間控制、報警、過溫保護、過壓保護、過流保護等功能。本充電器真正的實現了鉛酸蓄電池的三段式充電過程，其最高輸出功率可達90 W，效率約85%，成本不到20元，具有很高的市場競爭力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上傳時間： 2013-11-16
上傳用戶：cepsypeng
應用德國Micronas公司的CDC3207G微控制器開發了一款汽車儀表板系統。詳細地介紹了該系統的硬件原理，以及步進電機，音頻控制，LCD顯示，LED指示燈和報警燈等幾個模塊的實現方法。應用μC/OS-II實時操作系統開發軟件。著重介紹了啟動代碼的設計和任務的規劃。 Abstract: A dashboard system is developed by using CDC3207G microcontroller made by Micronas.The hardware of the sys-tem and the realization of the step motor module,audio module,LCD display and LED indicator and alarm module are ex-plained in detail.The μC/OS-II real-time operating system is used for the software development and the starting code design and the task planning is explained specifically.
上傳時間： 2013-10-26
上傳用戶：x4587
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上傳時間： 2013-11-16
上傳用戶：yare
為深入了解基于UC3854A控制的PFC變換器中的動力學特性，研究系統參數變化對變換器中分岔現象的影響，在建立Boost PFC變換器雙閉環數學模型的基礎上，用Matlab軟件對變換器中慢時標分岔及混沌等不穩定現象進行了仿真。在對PFC變換器中慢時標分岔現象仿真的基礎上，分析了系統參數變化對分岔點的影響，并進行了仿真驗證。仿真結果清晰地顯示了輸入整流電壓的幅值變化對系統分岔點的影響。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上傳時間： 2013-10-17
上傳用戶：杜瑩12345
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上傳時間： 2014-11-22
上傳用戶：xcy122677
