Developing internationalized products is a continuous balancing act. Developers and their managers often grossly underestimate the level of effort and attention to detail required to create either a world-ready, single-binary application ready for use in many different markets, or high-quality, foreign-language editions of a product. If you are a developer, make sure your management understands what is involved.
標簽： internationalized Developing Developers continuous
上傳時間： 2014-12-05
上傳用戶：TRIFCT
KEPware Automation DLL installation instructions: To use the KEPware Automation DLL in your Visual Basic project: 1) In the VB IDE, Select "Project/References". 2) If you have been using another vender s automation dll, uncheck it. For example, uncheck "OPC Automation 2.0" for the OPC Foundation s automation dll. 3) Check "KEPware OPC Automation 2.0". 4) Recompile your VB project. If you have been using the OPC Fondation s automation dll, you should not need to make any changes to the VB source code.
標簽： Automation KEPware installation instructions
上傳時間： 2013-12-28
上傳用戶：電子世界
CHAPT14\MODEM.CPP Implementation of the Modem class CHAPT14\MODEM.H Declarations of the Modem class CHAPT14\TSTMODEM.CPP 16-bit test program for the Modem class CHAPT14\TSTMODEM.EXE 16-bit executable of the test program CHAPT14\TSTMODEM.MAK Make file for use with Borland or Microsoft C
上傳時間： 2013-12-24
上傳用戶：壞天使kk
做嵌入式的串口設置時，可以直接把sct解壓了，然后直接make。 測試串口是否可以工作正常，很好的代碼。
上傳時間： 2013-12-11
上傳用戶：zhangliming420
// Copyright (c), Philips Semiconductors Gratkorn // (C)PHILIPS Electronics N.V.2000 // All rights are reserved. // Philips reserves the right to make changes without notice at any time. // Philips makes no warranty, expressed, implied or statutory, including but // not limited to any implied warranty of merchantibility or fitness for any //particular purpose, or that the use will not infringe any third party patent, // copyright or trademark. Philips must not be liable for any loss or damage // arising from its use.
標簽： Semiconductors Electronics Copyright Gratkorn
上傳時間： 2016-02-04
上傳用戶：xuanjie
Ideal for large low power (nanoWatt) and connectivity applications that benefit from the availability of four serial ports: double synchronous serial ports (I² C™ and SPI™ ) and double asynchronous (LIN capable) serial ports. Large amounts of RAM memory for buffering and FLASH program memory make it ideal for instrumentation panels, TCP/IP enabled embedded applications as well as metering and industrial control and monitoring applications. While operating up to 40 MHz, it is also backward software and hardware compatible with the PIC18F8720.
標簽： connectivity applications availabilit nanoWatt
上傳時間： 2016-02-04
上傳用戶：CHINA526
ADT600-1的基地址0x300,中斷為7， 3個定時器采用級連，CLK0的時鐘源是模塊上的8M震蕩器，中斷源為71054定時器的輸出OUT2。采集電壓范圍為+/-5V，請按《ADT200/ADT600技術手冊 版本B》上的說明對SW1，W5,W6,W9跳線。若你想修改中斷號和基地址，請修改config.h相應的常量ADT_IRQ, ADT_BASE定義,然后重新編譯安裝，即運行make all 注意:不要在其他文件中修改。
上傳時間： 2016-02-12
上傳用戶：evil
ADT600-1的基地址0x300,中斷為7， 3個定時器采用級連，CLK0的時鐘源是模塊上的8M震蕩器，中斷源為71054定時器的輸出OUT2。采集電壓范圍為+/-5V，請按《ADT200/ADT600技術手冊 版本B》上的說明對SW1，W5,W6,W9跳線。若你想修改中斷號和基地址，請修改config.h相應的常量ADT_IRQ, ADT_BASE定義,然后重新編譯安裝，即運行make all 注意:不要在其他文件中修改。
上傳時間： 2013-12-10
上傳用戶：tonyshao
ADT600-1的基地址0x300,中斷為7， 3個定時器采用級連，CLK0的時鐘源是模塊上的8M震蕩器，中斷源為71054定時器的輸出OUT2。采集電壓范圍為+/-5V，請按《ADT200/ADT600技術手冊 版本B》上的說明對SW1，W5,W6,W9跳線。若你想修改中斷號和基地址，請修改config.h相應的常量ADT_IRQ, ADT_BASE定義,然后重新編譯安裝，即運行make all 注意:不要在其他文件中修改。
上傳時間： 2013-12-25
上傳用戶：wl9454
oreilly的書一般都經典，具體看書吧，oreilly.managing.projects.with.gnu.make.3rd.edition
標簽： oreilly
上傳時間： 2014-08-23
上傳用戶：himbly
