Battery powered applications that have a signifi cantamount of time in standby mode, require electrical circuitsto operate with a low quiescent current to preserve batterylife. The LTC3835 synchronous step-down controlleris an excellent solution with its ultralow quiescent current(80μA). Other features make it uniquely qualifi ed tosatisfy the needs of automotive applications. A wide 4Vto 36V input voltage range protects the supply againsthigh input voltage transients and is compatible with lowvoltage cold crank conditions. The constant frequencycurrent-mode architecture with high-side inductor current
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
Automotive batteries, industrial power supplies, distributedsupplies and wall transformers are all sources ofwide-ranging high voltage inputs. The easiest way to stepdown these sources is with a high voltage monolithicstep-down regulator that can directly accept a wide inputrange and produce a well-regulated output. The LT®3493accepts inputs from 3.6V to 36V and LT3481 acceptsinputs from 3.6V to 34V. Both provide excellent lineand load regulation and dynamic response. The LT3481offers a high effi ciency solution over a wide load range andkeeps the output ripple low during Burst Mode® operationwhile the LT3493 provides a tiny solution with minimalexternal components. The LT3493 operates at 750kHzand the LT3481 has adjustable frequency from 300kHzto 2.8MHz. High frequency operation enables the use ofsmall, low cost inductors and ceramic capacitors.
Typical industrial and automotive applications requiremultiple high current, low voltage power supply solutionsto drive everything from disc drives to microprocessors.For many of these applications, particularly thosethat have size constraints, the LT3501® dual step-downconverter is an attractive solution because it’s compactand inexpensive compared to a 2-chip solution. The dualconverter accommodates a 3V to 25V input voltage rangeand is capable of supplying up to 3A per channel. Thecircuit in Figure 1 produces 3.3V and 1.8V.
Many telecommunications and computing applicationsneed high effi ciency step-down DC/DC converters thatcan operate from a very low input voltage. The highoutput power synchronous controller LT3740 is idealfor these applications, converting input supplies rangingfrom 2.2V to 22V to outputs as low as 0.8V with loadcurrents from 2A to 20A. Applications include distributedpower systems, point-of-load regulation and conversionof logic supplies.
Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
The LTC®4151 is a high side power monitor that includesa 12-bit ADC for measuring current and voltage, as wellas the voltage on an auxiliary input. Data is read throughthe widely used I2C interface. An unusual feature in thisdevice is its 7V to 80V operating range, allowing it to coverapplications from 12V automotive to 48V telecom.
As environmental concerns over traditional lighting increaseand the price of LEDs decreases, high power LEDsare fast becoming a popular lighting solution for offl ineapplications. In order to meet the requirements of offl inelighting—such as high power factor, high effi ciency, isolationand TRIAC dimmer compatibility—prior LED driversused many external discrete components, resulting incumbersome solutions. The LT®3799 solves complexity,space and performance problems by integrating all therequired functions for offl ine LED lighting.
