Abstract: As electronic systems take over many of the mechanical functions in a car—ranging from engine timing to steering andbraking—there is a growing concern about fault tolerance. There should not be a single point of failure that would prevent a car fromat least "limping" off the road or making it to the nearest service station. Redundant systems, watchdog timers, and other controlcircuits are used to reroute signals and perform other functions that ensure that a vehicle can safely make it off the road when afailure occurs.
Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads controlled in time.
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
設計一種基于AT89C52的語音錄放系統，利用單片機、ISD2560語音錄放器件、麥克風、揚聲器等元器件實現硬件電路的設計，并利用C51高級語言設計ISD2560器件控制字的寫入和定時中斷程序。經軟硬件調試，結果表明該系統錄放效果良好，具有一定的工程實用價值。
Abstract:
Voice recording and playback system based on AT89C52is designed in this paper.Using the single-chip microcomputer，voice recording and playback chip ISD2560，microphone and speaker to realize the hardware circuit design.Writing ISD2560control words and timing interrupt procedures are designed by C51advanced language.Through the hardware and software test,voice recording and playback system play better voice,and this system has some engineering practical values.
介紹基于ISA總線與KH-9300的數據采集板卡的設置，詳細說明8254定時計數器及8259中斷控制器的結構特點、工作方式、控制字等，探討中斷類型、中斷處理程序、中斷矢量表及其填寫。重點講述使用TorboC編寫中斷服務程序的方法，應注意的主要問題及程序測試的結果。
Abstract:
The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
針對眾多低成本數據采集需求，采用帶有片上USB控制器和D/A轉換器的混合信號微處理器C8051F340，設計了一款可通過USB接口和LabVIEW圖形用戶界面實現與PC機聯機的數據采集器，同時借助系統的SD卡存儲獨立實現現場長時間采集數據。該數據采集器成本低，結構簡單，體積小，已成功用于工業現場。
Abstract:
Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.
利用AT89C51型單片機定時和中斷功能，配以LM386型音頻功率放大器，構成了作息號音自動播放器，為學校和機關管理提供方便。
Abstract:
Using timing and interrupt function of the AT89C51 single-chip microcomputer and the LM386 audio power amplifier.It is constituted the automatic bugle player.This player facilitates the institution and the school daily management.
以S3C825A為例介紹三星公司SAM8系列單片機的內部結構及其軟件開發環境，詳細描述采用混合編程法來對SAM8系列單片機進行軟件設計的一般方法，最后給出用混合編程法對S3C825A進行軟件設計的具體應用實例。
Abstract:
With S3C825A,this paper firstly introduces the SAM8 series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 series single-chip microcontrollers. In the end, the application program is also given.
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
