Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上傳時間： 2013-10-12
上傳用戶：jinyao
Abstract: With its small size and large load (10W) capability, the MAX13256 H-bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a largecapacitance without going into fault.
上傳時間： 2013-10-20
上傳用戶：2728460838
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間： 2013-11-18
上傳用戶：hulee
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上傳時間： 2013-10-16
上傳用戶：togetsomething
為解決直流逆變交流的問題，有效地利用能源，讓電源輸出最大功率，設計了高性能的基于IR2101最大功率跟蹤逆變器，并以SPMC75F2413A單片機作為主控制器。高電壓、高速功率的MOSFET或IGBT驅動器IR2101采用高度集成的電平轉換技術，同時上管采用外部自舉電容上電，能夠穩定高效地驅動MOS管。該逆變器可以實現DC/AC的轉換，最大功率點的跟蹤等功能。實際測試結果表明，該逆變器系統具有跟蹤能力強，穩定性高，反應靈敏等特點，該逆變器不僅可應用于普通的電源逆變系統，而且可應用于光伏并網發電的逆變系統，具有廣泛的市場前景。 Abstract: To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上傳時間： 2013-11-17
上傳用戶：lliuhhui
本文分析了ARM-Linux下IIC總線及其設備驅動的層次結構，指出了IIC設備添加與驅動實現的途徑，詳細闡述了如何采用通用i2c-dev.c驅動常規IIC設備、如何編寫特定IIC設備的probe方式驅動、怎樣設計動態加載的簡易IIC“客服-驅動”、怎樣使用GPIO模擬IIC總線快速驅動設備等常用具體實現過程和關鍵環節，并說明了這些方法的優勢和不足。
標簽： ARM-Linux-IIC 設備 驅動實現
上傳時間： 2013-10-13
上傳用戶：xingisme
多媒體卡MMC(MultiMedia Card)是由美國SanDisk 公司和德國Simens 公司于1997 年共 同開發推出的一種多功能存儲卡。內置控制電路，可以使用在手機、數碼相機、MP3、PDA 等多種數字設備上，可反復記錄30 萬次。現在市場上的主流容量有128 MB～2 GB。 文中首先介紹單片機對SPI 協議下的MMC 卡的底層讀寫操作，然后分析MMC 卡文件系統 的結構，最后詳細說明MMC 卡文件的創建、讀寫、刪除等操作。該方法可應用到與Window s 有交互的嵌入式系統中，便于文件的統一管理。
上傳時間： 2013-11-05
上傳用戶：lionlwy
Designing read/write device (RWD) units for industrial RF-Identification applications is strongly facilitated by the NXP Semiconductors HITAG Reader Chip HTRC110. All needed function blocks, like the antenna driver, modulator demodulator and antenna diagnosis unit, are integrated in the HTRC110. Therefore only a minimum number of additional passive components are required for a complete RWD. This Application Note describes how to design an industrial RF-Identification system with the HTRC110. The major focus is dimensioning of the antenna, all other external components including clock and power supply, as well as the demodulation principle and its implementatio
上傳時間： 2013-10-22
上傳用戶：zhengjian
針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上傳時間： 2013-10-10
上傳用戶：asdfasdfd
AVR32801: UC3A3 Schematic Checklist Features • Power circuit • Reset circuit • USB connection • External bus interface • ABDAC sound DAC interface • JTAG and Nexus debug ports • Clocks and crystal oscillators • MMC, SD-card, SDHC, SDIO and CE-ATA interface 1 Introduction A good hardware design comes from a proper schematic. Since UC3A3 devices have a fair number of pins and functions, the schematic for these devices can be large and quite complex. This application note describes a common checklist which should be used when starting and reviewing the schematics for a UC3A3 design.
標簽： Schematic 32801 UC3A3 Chec
上傳時間： 2014-12-26
上傳用戶：DXM35
