在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上傳時間： 2014-01-21
上傳用戶：shen007yue
生成BCD碼。 Name: BIN3toBCD4 Func:2字節二進制整數--->>BCD碼四字節轉換(Comped BCD) Input: 3進制數人低字節到高字節存放在內部RAM50H，51H,52h單元中 Output: BCD碼人低位到高位分別存放在內部RAM53H,54H，55H，56H單元中 USE: R7-R0, 56H-50H
標簽： BCD BIN3toBCD4 Comped Input
上傳時間： 2015-02-02
上傳用戶：FreeSky
對c語言的簡單語法分析器 文件說明： input.txt內為輸入的源程序，包括for，while和if else控制等 output.txt內為輸出的二元單詞序列 k.txt為關鍵字表 l.txt為運算符和界符表 i.txt為該輸入的源程序的標志符 c.txt為常數表 個別表需要序列號，這時各表的序列號默認為從1開始，每行加1。 使用說明： 在提示符下輸入input.txt文件的路徑和文件名字， 運行完成后，打開文件output.txt看結果。
上傳時間： 2013-12-23
上傳用戶：pompey
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file. • Assume a file with correct data (no garbage, characters, etc.). • you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour: o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the next size for the next 2 matrices (if not end of file). o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
標簽： multiplication Implement matrices matrix
上傳時間： 2014-08-30
上傳用戶：dsgkjgkjg
* * Input * bin_data : binary data * bin_size : binary data length * Mode : operation mode * BASE64_NeedCRLF ---- Need a CRLF every 64 base64-character * BASE64_NotCRLF ---- Need not CRLF between 64 base64-character * * Output * char data * char data length * * Return * 0: success -1: error
標簽： binary data operation bin_data
上傳時間： 2015-06-04
上傳用戶：ZJX5201314
Routine mampres: To obtain amplitude response from h(exp(jw)). input parameters: h :n dimensioned complex array. the frequency response is stored in h(0) to h(n-1). n :the dimension of h and amp. fs :sampling frequency (Hz). iamp:If iamp=0: The Amplitude Res. amp(k)=abs(h(k)) If iamp=1: The Amplitude Res. amp(k)=20.*alog10(abs(h(k))). output parameters: amp :n dimensioned real array. the amplitude-frequency response is stored in amp(0) to amp(n-1). Note: this program will generate a data file "filename.dat" . in chapter 2
標簽： dimensione parameters amplitude response
上傳時間： 2013-12-19
上傳用戶：xfbs821
Routine mar1psd: To compute the power spectum by AR-model parameters. Input parameters: ip : AR model order (integer) ep : White noise variance of model input (real) ts : Sample interval in seconds (real) a : Complex array of AR parameters a(0) to a(ip) Output parameters: psdr : Real array of power spectral density values psdi : Real work array in chapter 12
標簽： parameters AR-model Routine mar1psd
上傳時間： 2015-06-09
上傳用戶：playboys0
對讀入的某個文本文件input.txt中，拆出英文單詞，輸出一個按字典順序排列的單詞表，結果輸出在文本文件output.txt中，每個單詞一行，并在單詞后輸出該單詞出現的個數，兩個字段之間用逗號分隔。約定單詞僅由英文字母組成，單詞間由非英文字母分隔，相同單詞只輸出一個，大小寫不區分。 利用二叉樹實現
上傳時間： 2015-07-04
上傳用戶：yulg
h.263 c編碼源碼。目錄下有input。qcif原始未壓縮文件，運行程序生成重建文件recon。qcif和壓縮后文件output。263文件。
上傳時間： 2013-12-19
上傳用戶：ljmwh2000
工程計算MATLAB code to calculate the reorthogonalized sine tapers input: N = the length of the time series data to be tapered p = the number of tapers requested I = the gap structure a vector of length N I(t) = 1 if there is data at time t, t=1, ..., N I(t) = 0 if there is a gap at time t output: X = N-by-p vector of the reorthogonalized sine taper
標簽： the reorthogonalized calculate MATLAB
上傳時間： 2013-12-17
上傳用戶：wangyi39
