Construction Strategy of ESD Protection CircuitAbstract： The principles used to construct ESD protection on circuits and the basic conceptions of ESD protection design are presented.Key words：ESD protection/On circuit, ESD design window, ESD current path1 引言靜電放電（ESD，Electrostatic Discharge）給電子器件環境會帶來破壞性的后果。它是造成集成電路失效的主要原因之一。隨著集成電路工藝不斷發展，互補金屬氧化物半導體（CMOS，Complementary Metal-Oxide Semiconductor）的特征尺寸不斷縮小，金屬氧化物半導體(MOS, Metal-Oxide Semiconductor)的柵氧厚度越來越薄，MOS 管能承受的電流和電壓也越來越小，因此要進一步優化電路的抗ESD 性能，需要從全芯片ESD 保護結構的設計來進行考慮。
The outputs of the PCA9518 are immediately available as soon as there is a voltage present on thesupply >~1V and behave as described above. The power-on reset of the PCA9518A keeps the outputsturned off during power-up and maintains the high impedance of the outputs throughout the power-upcycle. There is an additional built-in delay after power-up that allows the analog circuits to stabilize beforethe part is activated.
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
提出了一個由AT89C52單片機控制步進電機的實例。可以通過鍵盤輸入相關數據, 并根據需要, 實時對步進電機工作方式進行設置, 具有實時性和交互性的特點。該系統可應用于步進電機控制的大多數場合。實踐表明, 系統性能優于傳統的步進電機控制器。關鍵詞: 單片機; 步進電動機; 直流固態繼電器; 實時控制Con trol System of Stepp ingMotor Ba sed on AT89C52 ChipM icrocomputerMENGWu2sheng, L ILiang (College of Automatization, Northwestern Polytechnical Unversity, Xipan 710072, China)ABSTRACT: A stepp ing motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi tional stepp ing motor controller.KEY WORDS: Chip microcomputer; Stepp ingmotor; DCSSR; Real2time control
CGAL is a collaborative effort of several sites in Europe and Israel. The goal is to make the most important of the solutions and methods developed in computational geometry available to users in industry and academia in a C++ library. The goal is to provide easy access to useful, reliable geometric algorithms
