-
Here an embedded System-on-chip is build, in an Xilinx Spartan-3 FPGA with Microblaze as the processor.A PLB core System is made with the VGA IP core attached to it. The software written for the MicroBlaze processor specifies the object, the color and the movement of the display. The functionality of the module is verified by implementation on Spartan 3.
標簽：
System-on-chip
Microblaze
embedded
Spartan
上傳時間：
2013-12-20
上傳用戶：上善若水
-
介紹幾種cpuThe 8xC251SA/SB/SP/SQ improves on the MCS-51 architecture and peripheral features, introducing the advanced register based CPU architecture i.e., the MCS 251 microcontroller architecture. The register based CPU supports a 40-byte register file. In addition, the 8xC251SA/SB/SP/SQ microcontroller has 256-Kbyte expanded external code/data memory space and 64-Kbyte stack space. The new controller is also specially designed to execute C code efficiently. More importantly, the 8xC251SA/SB/SP/SQ maintains binary code compatibility with MCS 51 microcontrollers but at the same time allows the use of the powerful MCS 251 microcontroller instruction set, with many new 8, 16 and 32 bit instructions available. The 8xC251SA/SB/SP/SQ has 512 bytes or 1 Kbyte of on-chip data RAM options and is available in 16 Kbytes and 8 Kbytes of on-chip ROM/OTPROM or ROMless options.
標簽：
architecture
introducin
peripheral
improves
上傳時間：
2015-03-15
上傳用戶：ccclll
-
Atmel’s AT91SAM7FP105 is a low pincount FingerChip processor based on the 32-bit ARM
RISC processor. It features a on-chip biometric engine performing enrollment verification and
identification, an internal record cache of up to 25 records and a secure command protocol over
USB, SPI, UART. This protocol enables an external host system or processor to control the onchip
bioengine functions, manipulate the record cache, and securely export record cache
records for external storage. Together with the FingerChip sensor device AT77C104B, it forms
an embedded, secured biometric turnkey solution.
標簽：
processor
FingerChip
pincount
Atmel
上傳時間：
2013-12-26
上傳用戶：shawvi
-
信號與信息處理是信息科學中近幾年來發展最為迅速的學科之一,隨著片上系統(SOC,System On Chip)時代的到來,FPGA正處于革命性數字信號處理的前沿。基于FPGA的設計可以在系統可再編程及在系統調試,具有吞吐量高,能夠更好地防止授權復制、元器件和開發成本進一步降低、開發時間也大大縮短等優點。然而,FPGA器件是基于SRAM結構的編程工藝,掉電后編程信息立即丟失,每次加電時,配置數據都必須重新下載,并且器件支持多種配置方式,所以研究FPGA器件的配置方案在FPGA系統設計中具有極其重要的價值,這也給用于可編程邏輯器件編程的配置接口電路和實驗開發設備提出了更高的要求。 本論文基于IEEE1149.1標準和USB2.0技術,完成了FPGA配置接口電路及實驗開發板的設計與實現。作者在充分理解IEEE1149.1標準和USB技術原理的基礎上,針對Altcra公司專用的USB數據配置電纜USB-Blaster,對其內部工作原理及工作時序進行測試與詳細分析,完成了基于USB配置接口的FPGA芯片開發實驗電路的完整軟硬件設計及功能時序仿真。作者最后進行了軟硬件調試,完成測試與驗證,實現了對Altera系列PLD的配置功能及實驗開發板的功能。 本文討論的USB下載接口電路被驗證能在Altera的QuartusII開發環境下直接使用,無須在主機端另行設計通信軟件,其兼容性較現有設計有所提高。由于PLD(Programmable Logic Device)廠商對其知識產權嚴格保密,使得基于USB接口的配置電路應用受到很大限制,同時也加大了自行對其進行開發設計的難度。 與傳統的基于PC并口的下載接口電路相比,本設計的基于USB下載接口電路及FPGA實驗開發板具有更高的編程下載速率、支持熱插拔、體積小、便于攜帶、降低對PC硬件傷害,且具備其它下載接口電路不具備的SignalTapII嵌入式邏輯分析儀和調試NiosII嵌入式軟核處理器等明顯優勢。從成本來看,本設計的USB配置接口電路及FPGA實驗開發板與其同類產品相比有較強的競爭力。
標簽：
FPGA
USB
2.0
上傳時間：
2013-04-24
上傳用戶：lingduhanya
-
如今IC設計進入了SOC(System-on-chip)設計時代。SOC是指在單一芯片上集成了微控制器、數字信號處理器、存儲器、I/O接口等，可以實現信號采集、轉換、存儲、處理等功能的芯片。SOC設計是基于IP可重用性的設計過程。現在已有不少公司成功地開發了各種SOC總線規范，以便于IP核的可復用性設計。其中，ARM公司開發的AMBA(Advanced Microcontroller Bus Arehitecture)規范已經成為嵌入式應用的行業標準。嵌入式SOC芯片廣泛應用于消費電子產品中，近年來隨著彩屏手機、PDA等移動終端的普及，液晶電視等平板顯示器件的推廣，液晶顯示器已經逐漸取代CRT成為主流的顯示器件。LCD Driver IC作為液晶顯示器的重要部件，需求量也日益增大。嵌入式液晶顯示系統的設計是當今SOC設計中不可缺少的部分，而基于AMBA總線規范的LCD顯示系統更是具備良好的性能和較大的潛力。 本文提出了一種基于AMBA總線規范的彩色TFT-LCD數字圖像顯示解決方案，硬件設計上包括APB存儲接口模塊、LCD控制模塊，并用VHDL硬件描述語言進行了功能仿真，采用Mentor公司Modelsim5.8完成了系統功能驗證；軟件設計上完成了基于SAMSUNG公司S6D0110 TFT-LCD驅動芯片的測試程序的編寫和系統測試。本設計不需要掌握TFT-LCD內部構造，復雜的內部驅動原理，只需要掌握AMBA總線規范和LCD的MPU并行接口時序，采用本課題設計出的LCD顯示控制模塊簡單實用，便于推廣應用。 本課題基于Xilinx公司的VirtexⅡ FF1152 PROTO開發平臺完成了軟件調試，實現了TFT-LCD圖像顯示。調試結果表明硬件和軟件設計正確且取得了較為滿意的結果。
標簽：
TFTLCD
顯示系統
上傳時間：
2013-06-02
上傳用戶：小楓殘月
-
信號與信息處理是信息科學中近幾年來發展最為迅速的學科之一,隨著片上系統(SOC,System On Chip)時代的到來,FPGA正處于革命性數字信號處理的前沿。基于FPGA的設計可以在系統可再編程及在系統調試,具有吞吐量高,能夠更好地防止授權復制、元器件和開發成本進一步降低、開發時間也大大縮短等優點。然而,FPGA器件是基于SRAM結構的編程工藝,掉電后編程信息立即丟失,每次加電時,配置數據都必須重新下載,并且器件支持多種配置方式,所以研究FPGA器件的配置方案在FPGA系統設計中具有極其重要的價值,這也給用于可編程邏輯器件編程的配置接口電路和實驗開發設備提出了更高的要求。 本論文基于IEEE1149.1標準和USB2.0技術,完成了FPGA配置接口電路及實驗開發板的設計與實現。作者在充分理解IEEE1149.1標準和USB技術原理的基礎上,針對Altcra公司專用的USB數據配置電纜USB-Blaster,對其內部工作原理及工作時序進行測試與詳細分析,完成了基于USB配置接口的FPGA芯片開發實驗電路的完整軟硬件設計及功能時序仿真。作者最后進行了軟硬件調試,完成測試與驗證,實現了對Altera系列PLD的配置功能及實驗開發板的功能。 本文討論的USB下載接口電路被驗證能在Altera的QuartusII開發環境下直接使用,無須在主機端另行設計通信軟件,其兼容性較現有設計有所提高。由于PLD(Programmable Logic Device)廠商對其知識產權嚴格保密,使得基于USB接口的配置電路應用受到很大限制,同時也加大了自行對其進行開發設計的難度。 與傳統的基于PC并口的下載接口電路相比,本設計的基于USB下載接口電路及FPGA實驗開發板具有更高的編程下載速率、支持熱插拔、體積小、便于攜帶、降低對PC硬件傷害,且具備其它下載接口電路不具備的SignalTapII嵌入式邏輯分析儀和調試NiosII嵌入式軟核處理器等明顯優勢。從成本來看,本設計的USB配置接口電路及FPGA實驗開發板與其同類產品相比有較強的競爭力。
標簽：
實驗
評估板
上傳時間：
2013-06-07
上傳用戶：2525775
-
Radio Frequency Integrated Circuit Design
I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
標簽：
Rogers
Radio
John
Freq
上傳時間：
2014-12-23
上傳用戶：han_zh
-
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
標簽：
3052A
3052
CN
鋰離子電池
上傳時間：
2013-11-10
上傳用戶：子虛烏有
-
MG3500SoC是支持H.264高清編解碼器的片上系統，內部集成一個嵌入式ARM926處理器，支持高清H.264編解碼、MPEG鄄2解碼和JPEG編解碼。介紹了MG3500SoC的主要性能特點、引腳排列、主要接口功能及在DVR上的應用，以及MG3500SoC及其周圍器件的硬件設計，提出了在設計中應注意的問題。
Abstract:
The MG3500System-on-chip（SoC）is high definition（HD）H.264codec,including ARM926-EJ processor，H.264encoder/decoder，MPEG2decoder and JPEG/MJPEG encoder/decoder.The features,pin assignments，interfaces and the typical application of MG3500in DVR are introduced in this paper.The application hardware circuit between the MG3500SoC and peripheral device are given,the questions which the syetem design needs to pay attention are explained.
標簽：
3500
264
MG
編解碼器
上傳時間：
2013-11-12
上傳用戶：elinuxzj
-
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· on-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
標簽：
2116
PCF
LCD
驅動器芯片
上傳時間：
2013-11-08
上傳用戶：laozhanshi111
