LinCAN is a Linux kernel module that implements a CAN driver capable of working with multiple cards, even with different chips and IO methods. Each communication object can be accessed from multiple applications concurrently. It supports RT-Linux, 2.2, 2.4, and 2.6 with fully implemented select, poll, fasync, O_NONBLOCK, and O_SYNC semantics and multithreaded read/write capabilities. It works with the common Intel i82527, Philips 82c200, and Philips SJA1000 (in standard and PeliCAN mode) CAN controllers. LinCAN project is part of a set of CAN/CANopen related components developed as part of OCERA framework.
標簽： implements multiple capable working
上傳時間： 2015-10-14
上傳用戶：磊子226
Avalon Interface Specification,The Avalon interface specification is designed to accommodate peripheral development for the system-on-a-programmable-chip (SOPC) environment. The specification provides peripheral designers with a basis for describing the address-based read/write interface found on master and slave peripherals, such as microprocessors, memory, UART, timer, etc.
標簽： Avalon Specification specification accommodate
上傳時間： 2014-03-06
上傳用戶：pompey
Flash Low Level Driver Code，can read/write all flash memory
上傳時間： 2014-01-24
上傳用戶：libenshu01
ST7529液晶驅動 The ST7529 is a driver & controller LSI for 32 gray scale graphic dot-matrix liquid crystal display systems. It generates 255 Segment and 160 Common driver circuits. This chip is connected directly to a microprocessor, accepts Serial Peripheral Interface (SPI), 8-bit/16-bit parallel or IIC display data and stores in an on-chip display data RAM. It performs display data RAM read/write operation with no external operating clock to minimize power consumption. In addition, because it contains power supply circuits necessary to drive liquid crystal, it is possible to make a display system with the fewest components.
標簽： 7529 controller dot-matrix graphic
上傳時間： 2013-12-02
上傳用戶：奇奇奔奔
S29NS-J 128 Megabit (8 M x 16-Bit), 64 Megabit (4 M x 16-Bit), 32 Megabit (2 M x 16-Bit), and 16 Megabit (1 M x 16 Bit), 110 nm CMOS 1.8-Volt only Simultaneous Read/Write, Burst Mode Flash Memories Data Sheet
上傳時間： 2014-01-01
上傳用戶：qoovoop
linux文件系統試驗 一、實驗目的 學習有關linux文件管理程序如何組織的知識，為簡化的文件系統設計并實現一組目錄操作。實驗中使用軟盤的fat12格式，設計一個程序可以對這種格式的磁盤進行一組目錄操作。 實驗使用了部分linux的系統調用，比如說open() sleek() read() write()幾個調用。通過此實驗來對linux的文件系統的管理有進一步的理解。 二、實驗要求 主要實現三個功能：一 讀取磁盤目錄的目錄列表。(命令輸入 ls ) 二 切換目錄（不處理路徑名）。（命令輸cd dir_name 或cd/ 或cd.. ） 三 刪除當前目錄下的文件。（命令輸入 del filename ）
上傳時間： 2014-01-17
上傳用戶：
單片機操作ＭＭＣ／ＳＤ卡讀寫fat12/16/32文件系統的程序，外國網站找到的，支持文件open,read write mkdir close 等，基本pc文件功能都支持，專門針對8位mcu，方便移植到各種單片機系統，占用資源很少
上傳時間： 2016-03-24
上傳用戶：yuanyuan123
This program accesses a SPI EEPROM using polled mode access. The F12x MCU is configured in 4-wire Single Master Mode, and the EEPROM is the only slave device connected to the SPI bus. The read/write operations are tailored to access a Microchip 4 kB EEPROM
標簽： configured accesses program EEPROM
上傳時間： 2016-03-29
上傳用戶：gut1234567
// This program accesses a SPI EEPROM using polled mode access. The F06x MCU // is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the SPI bus. The read/write operations are // tailored to access a Microchip 4 kB EEPROM 25LC320. The relevant hardware // connections of the F06x MCU are shown here:
標簽： configured accesses program EEPROM
上傳時間： 2014-01-18
上傳用戶：liglechongchong
// This program accesses a SPI EEPROM using polled mode access. The F06x MCU // is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the SPI bus. The read/write operations are // tailored to access a Microchip 4 kB EEPROM 25LC320. The relevant hardware // connections of the F06x MCU are shown here:
標簽： configured accesses program EEPROM
上傳時間： 2016-04-12
上傳用戶：qb1993225
<table id="62u2u"></table>