this program reads data from sensors and then sends it to a PIC-WEB which then loads it to a server and stores it into a database.
標簽： then program PIC-WEB sensors
上傳時間： 2013-12-30
上傳用戶：1101055045
reads stl files in matlab
上傳時間： 2013-12-13
上傳用戶：gundamwzc
·詳細說明：c51讀取gps并電臺通訊的源代碼-c51 reads takes gps and the broadcasting station communication source code
上傳時間： 2013-06-01
上傳用戶：徐孺
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
上傳時間： 2013-10-26
上傳用戶：yuzsu
IEEE1394Diag is a GUI application that presents a graphical view of an IEEE1394 network and provides the ability to perform common 1394 operations such as async reads, writes, isoc listens and talks, as well as configuration rom browsing of all nodes present on a bus.
標簽： IEEE 1394 application graphical
上傳時間： 2015-04-02
上傳用戶：familiarsmile
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
標簽： microcontroll Converter configure following
上傳時間： 2014-12-01
上傳用戶：獨孤求源
IEEE1394Diag is a GUI application that presents a graphical view of an IEEE1394 network and provides the ability to perform common 1394 operations such as async reads, writes, isoc listens and talks, as well as configuration rom browsing of all nodes pres
標簽： IEEE 1394 application graphical
上傳時間： 2014-12-03
上傳用戶：123啊
About transforms DCT using the separate cosine jpeg the compression the matlab source program, simple is practical, also has the annotation, very good reads. ,matlab,Wavelet
標簽： the compression transforms separate
上傳時間： 2013-11-26
上傳用戶：努力努力再努力
The view238 application is a simple tool for graphically displaying STEP-NC toolpaths. It is a Java application that reads AP-238 XML data using the DOM inferface, then finds and display the toolpaths within. At present, only polylines, and circular arcs are processed.
標簽： application graphically displaying toolpaths
上傳時間： 2013-12-02
上傳用戶：zhangliming420
EPS_Java Projec is JAVA program can display charts, and handle waypoints, track, and routes. It reads output from the gpstrans program. gpstrans can communicate with Garmin GPS navigators.
標簽： and waypoints EPS_Java display
上傳時間： 2016-01-22
上傳用戶：2404
