為解決我國水位監測野外條件下長期無人看守的問題，研制開發了基于MSP430單片機的智能水位計。從其組成到各功能分別進行了詳細的介紹，該智能水位計不僅實現了水位數據的實時監測、記錄和定期采集等多種工作模式，而且提高了水位監測精度，實現了水位監測的智能化。
Abstract:
In order to solve the problems of long-term unmanned observation in the field water monitoring，an intelligence water-level meter based on MSP430 is developed composition and every function moduce of the water level meter was introduced in detail. It not only realizes water level data collection and storage， regularly gathering and so on， but also improves the water-level precision ， finally realizes the intelligence.
為了使音頻信號分析儀小巧可靠，成本低廉，設計了以2片MSP430F1611單片機為核心的系統。該系統將音頻信號送入八階巴特沃茲低通濾波器，對信號進行限幅放大、衰減、電平位移、緩沖，并利用一單片機負責對前級處理后的模擬信號進行采樣，將采集得到的音頻信號進行4 096點基2的FFT計算，并對信號加窗函數提高分辨率，另一單片機負責對信號的分析及控制顯示設備。此設計精確的測量了音頻信號的功率譜、周期性、失真度指標，達到較高的頻率分辨率，并能將測量結果通過紅外遙控器顯示在液晶屏上。
Abstract:
o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
提出一種基于凌陽單片機的步進電機加減速的控制方法。采用凌陽科技推出的16位結構工控單片機SPMC75F2413A為控制器，由Allegro公司生產的兩相步進電機專用驅動器件SLA7042M構成步進電機的驅動電路，在傳統的3段直線加減速控制算法基礎上增加至7段S形曲線加減速過程，控制步進電機的啟動和停止。實驗結果表明，該控制方法克服了直線加減速中不連續、易造成系統沖擊的問題，整個系統實現柔性控制，電機啟動、停止連續性能提高30%。
Abstract:
The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。
Abstract:
A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
CAN與RS232轉換節點的設計與實現
介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
The super-junction structure, which has P-type pillar layers as shown left,
realizes high withstand voltage and ON-resistance lower than the conventional
theoretical limit of silicon.
This thesis has recommended mainly systematic design and simulation of the bank ATM (ATM ) realize the course, and has introduced each function module of this system in detail , including deposit and withdraw, transfer accounts, inquire about, revise the concrete course that realize in password and concrete course that realizes of the module
In this paper, it is designed a platform for least deviation linear interpolation with two axis linear guides, and it realizes the linear interpolator by PIC microprocessor with MPLAB C language in PIC microprocessor.
以STC12C5A60S2單片機為控制核心,采用2.4G(JF24D)無線遙控模塊進行無線發射與接收,設計了一種雙電機遙控船模控制系統.該系統通過切換檔桿實現前進后退,方向盤左右轉動、暫停按鈕等控制直流電機的正轉、反轉、暫停,使得電機驅動的遙控船模實現前進后退、左右轉向、暫停等功能,有效解決了驅動功率小和船模之間相互干擾等問題,可廣泛應用于遙控船模領域.Using STC12C5A60S2 single-chip microcomputer as the controller and 2.4 G(JF24D)wireless remote control module for wireless transmission and reception, a dual-motor remote control ship model control system is designed. The system realizes forward and backward by switching the gear lever. The steering wheel rotates left and right and the pause button controls the forward, reverse and pause of the dc motor. The remote controller of ship model driven by the motor realizes forward and backward, left and right steering, pause and other functions. The ship model control system can effectively solve the problems of small driving power and mutual interference between ship models, and can be widely used in the field of remote controller of ship model.
