There are two files in the zip folder. bpsk_spread.m and jakesmodel.m Steps for simulation: 1] Run jakesmodel.m first 2] Then run bpsk_spread.m . 3] Note that during the first run bpsk_spread.m has no rayleigh fading.This is because the corresponding code has been commented 4] The resulting performance is stored in BER_awgn. 5] Now uncomment the Rayleigh Fading code in bpsk_spread.m file. 6] Same time comment BER_awgn (line 112) and uncomment BER_ray variable. 7] Run the simulation. To compare the perfromances of the receiver using DSSS plot the BER_awgn and BER_ray
標簽： bpsk_spread jakesmodel simulation folder
上傳時間： 2016-05-19
上傳用戶：ynsnjs
Matlab is an ideal tool for simulating digital communications systems, thanks to its easy scripting language and excellent data visualization capabilities. One of the most frequent simulation tasks in the field of digital communications is bit-error- rate testing of modems. The bit-error-rate performance of a receiver is a figure of merit that allows different designs to be compared in a fair manner. Performing bit-error-rate testing withMatlab is very simple, but does require some prerequisite knowledge
標簽： communications simulating scripting digital
上傳時間： 2014-01-02
上傳用戶：plsee
M-file uses random data which BPSK modulates a carrier to configure a BPSK UWB transmitter. The receiver demodulates the BPSK UWB carrier and the data is recovered.
標簽： BPSK transmitter configure modulates
上傳時間： 2013-12-30
上傳用戶：偷心的海盜
M-file uses random data which BPSK modulates a carrier to configure a BPSK UWB transmitter. The receiver demodulates the BPSK UWB carrier and the data is recovered.
標簽： BPSK transmitter configure modulates
上傳時間： 2014-08-09
上傳用戶：skfreeman
This m file models a UWB system using BPSK with the fifth order derivative of the gaussian pulse with correlation receiver and intgrator.
標簽： derivative the gaussian models
上傳時間： 2016-06-28
上傳用戶：xuanjie
pashload是應用在linux下的網絡帶寬測試源程序精確度比較高 ///////////////////////////////////// Pathload is a tool for estimating the available bandwidth of an end-to-end path from a host S (sender) to a host R (receiver). The available bandwidth is the maximum IP-layer throughput that a flow can get in the path from S to R, without reducing the rate of the rest of the traffic in the path.
標簽： pashload Pathload linux tool
上傳時間： 2016-06-29
上傳用戶：xzt
The source codes are from the "Simulation and software Radio for mobile communication" It contain the channel model and CDMA Transmitter and receiver.
標簽： communication Simulation software contain
上傳時間： 2016-08-06
上傳用戶：z754970244
The MAX481E, MAX483E, MAX485E, MAX487E–MAX491E, and MAX1487E are low-power transceivers for RS-485 and RS-422 communications in harsh environments. Each driver output and receiver input is protected against ±15kV electrostatic discharge (ESD) shocks, without latchup. These parts contain one driver and one receiver. The MAX483E, MAX487E, MAX488E, and MAX489E feature reduced slewrate drivers that minimize EMI and reduce reflections caused by improperly terminated cables, thus allowing error-free data transmission up to 250kbps. The driver slew rates of the MAX481E, MAX485E, MAX490E, MAX491E, and MAX1487E are not limited, allowing them to transmit up to 2.5Mbps.
標簽： MAX transceivers 485 low-power
上傳時間： 2013-12-22
上傳用戶：小寶愛考拉
The idea behind differential GPS is to remove as much errors as possible from the range measurements by establishing these errors at a reference site. In its most simple setup, a GPS receiver is located at a well surveyed position and its (pseudo) range measurements are compared with the actual calculated range from this receiver to the SV s. The differences between measured ranges and calculated ranges at the reference receiver are applied as corrections to the ranges measured by other receiver(s) close by.
標簽： differential measurements possible behind
上傳時間： 2013-12-19
上傳用戶：zgu489
Modify the Gray-coded modulation example (COMMDOC_GRAY) so that it uses a pair of square root raised cosine filters to perform pulse shaping and matched filtering at the transmitter and receiver, respectively.
標簽： COMMDOC_GRAY Gray-coded modulation example
上傳時間： 2017-01-08
上傳用戶：zhangzhenyu
