The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上傳時間： 2013-10-11
上傳用戶：dianxin61
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
標簽： Infra-red Remote Cont 05K
上傳時間： 2014-01-24
上傳用戶：zl5712176
The Original USB 2.0 specification released on April 27, 2000 Errata to the USB 2.0 specification as of December 7, 2000 Mini-B connector Engineering Change Notice to the USB 2.0 specification. Pull-up/pull-down resistors Engineering Change Notice to the USB 2.0 specification. Errata to the USB 2.0 specification as of May 28, 2002 Interface Association Descriptor Engineering Change Notice to the USB 2.0 specification. Rounded Chamfer Engineering Change Notice to the USB 2.0 specification as of October 8, 2003 Unicode Engineering Change Notice to the USB 2.0 specification as of February 21, 2005 Inter-Chip USB Supplement Revision 1.0 as of March 13, 2006 Revision 1.3 of the USB On-The-Go Supplement as of December 5, 2006 Revision 1.01 of the Micro-USB Cables and Connectors Specification as of April 4, 2007 USB 2.0 Link Power Management Addendum Engineering Change Notice to the USB 2.0 specification as of July 16, 2007.
標簽： specification 2.0 USB Original
上傳時間： 2013-12-31
上傳用戶：familiarsmile
The SL74HC573 is identical in pinout to the LS/ALS573. The device inputs are compatible with standard CMOS outputs with pullup resistors, they are compatible with LS/ALSTTL outputs. These latches appear transparent to data (i.e., the outputs change asynchronously) when Latch Enable is high. When Latch Enable goes low, data meeting the setup and hold time becomes latched.
標簽： compatible The 573 identical
上傳時間： 2016-12-29
上傳用戶：變形金剛
Video-DVM is a very cheap DVM that shows how an output as complex as a videocomposite signal can be generated entirely in software: two I/O pins and three resistors are all the hardware required. Connected to any TV set it displays voltages, included max and min peaks, using both giant digits and an analog bar-display . A serial data output for computer data logging is provided, too.
標簽： videocomposite Video-DVM complex output
上傳時間： 2014-12-09
上傳用戶：xuan‘nian
The AZ1117 is a series of low dropout three-terminal regulators with a dropout of 1.15V at 1A output current. The AZ1117 series provides current limiting and thermal shutdown. Its circuit includes a trimmed bandgap reference to assure output voltage accuracy to be within 1% for 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 5.0V and adjustable versions or 2% for 1.2V version. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal shutdown provides protection against any combination of overload and ambient temperature that would create excessive junction temperature. The AZ1117 has an adjustable version, that can provide the output voltage from 1.25V to 12V with only 2 external resistors.
上傳時間： 2019-04-11
上傳用戶：heaven0o0o0
Wherever possible the overall technique used for this series will be "definition by example" withgeneric formulae included for use in other applications. To make stability analysis easy we will usemore than one tool from our toolbox with data sheet information, tricks, rules-of-thumb, SPICESimulation, and real-world testing all accelerating our design of stable operational amplifier (op amp)circuits. These tools are specifically targeted at voltage feedback op amps with unity-gain bandwidths<20 MHz, although many of the techniques are applicable to any voltage feedback op amp. 20 MHz ischosen because as we increase to higher bandwidth circuits there are other major factors in closing theloop: such as parasitic capacitances on PCBs, parasitic inductances in capacitors, parasitic inductancesand capacitances in resistors, etc. Most of the rules-of-thumb and techniques were developed not justfrom theory but from the actual building of real-world circuits with op amps <20 MHz.
標簽： 運算放大器
上傳時間： 2021-11-01
上傳用戶：
蟲蟲下載站版權所有 京ICP備2021023401號-1
