The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for
SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register,
8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption
and a high-impedance open-drain output pin, IO0.
The system master can enable the PCA9557’s I/O as either input or output by writing to
the configuration register. The system master can also invert the PCA9557 inputs by
writing to the active HIGH polarity inversion register. Finally, the system master can reset
the PCA9557 in the event of a time-out by asserting a LOW in the reset input.
The power-on reset puts the registers in their default state and initializes the
I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to
occur without de-powering the part.
6小時學會labview,
labview Six Hour Course – Instructor Notes
This zip file contains material designed to give students a working knowledge of labview in a 6 hour timeframe. The contents are:
Instructor Notes.doc – this document.
labviewIntroduction-SixHour.ppt – a PowerPoint presentation containing screenshots and notes on the topics covered by the course.
Convert C to F (Ex1).vi – Exercise 1 solution VI.
Convert C to F (Ex2).vi – Exercise 2 solution subVI.
Thermometer-DAQ (Ex2).vi – Exercise 2 solution VI.
Temperature Monitor (Ex3).vi – Exercise 3 solution VI.
Thermometer (Ex4).vi – Exercise 4 solution subVI.
Convert C to F (Ex4).vi – Exercise 4 solution subVI.
Temperature Logger (Ex4).vi – Exercise 4 solution VI.
Multiplot Graph (Ex5).vi – Exercise 5 solution VI.
Square Root (Ex6).vi – Exercise 6 solution VI.
State Machine 1 (Ex7).vi – Exercise 7 solution VI.
The slides can be presented in two three hour labs, or six one hour lectures. Depending on the time and resources available in class, you can choose whether to assign the exercises as homework or to be done in class. If you decide to assign the exercises in class, it is best to assign them in order with the presentation. This way the students can create VI’s while the relevant information is still fresh. The notes associated with the exercise slide should be sufficient to guide the students to a solution. The solution files included are one possible solution, but by no means the only solution.
This firmware translates a PS/2 mouse to a USB mouse. The translator
firmware is entirely interrupt driven (with the exception of sending the
data via USB to the host.) An interrupt is generated when the PS/2 start
bit is received, at which time the firmware will begin its receive routine.
In addition to this interrupt, every 168ms a timer overflow interrupts the
main program and implements one state of the mouse state machine. This
state machine handles sending bytes to and translating bytes received from
the PS/2 mouse automatically. All of this is done in the background while
the main program runs in the foreground. The only operation that the main
program implements is sending mouse data to the PC via USB.
Verilog and VHDL狀態機設計，英文pdf格式
State machine design techniques for Verilog and VHDL
Abstract : Designing a synchronous finite state Another way of organizing a state machine (FSM) is a common task for a digital logic only one logic block as shown in
engineer. This paper will discuss a variety of issues regarding FSM design using Synopsys Design Compiler . Verilog and VHDL coding styles will be 2.0 Basic HDL coding
presented. Different methodologies will be compared using real-world examples.
this a pack include source code for quartus 2.
It is an implementation of the LC2. The LC-2 computer is described in Introduction to Computing Systems from Bits & Gates to C & Beyond by Yale Patt and Sanjay Patel, McGraw Hill, 2001. The LC2 model can be run as a simulation or downloaded to the UP3 in a larger model, TOP_LC2 that adds video output. Push buttons reset and single step the processor and a video output display of registers is generated. This state machine VHDL-based model of the LC-2 includes all source files. Currently compiled for a Cyclone EP1C6Q240 FPGA.
The VGA example generates a 320x240 diffusion-limited-aggregation (DLA) on Altera DE2 board. A DLA is a clump formed by sticky particles adhering to an existing structure. In this design, we start with one pixel at the center of the screen and allow a random walker to bounce around the screen until it hits the pixel at the center. It then sticks and a new walker is started randomly at one of the 4 corners of the screen. The random number generators for x and y steps are XOR feedback shift registers (see also Hamblen, Appendix A). The VGA driver, PLL, and reset controller from the DE2 CDROM are necessary to compile this example. Note that you must push KEY0 to start the state machine.
it is a verilog code written for traffic light controller will synthesize in xinlix ise 8.2i.i have tested it om my kit.[i mae my own kit for spartan2 device].it is a state machine based code.
