<li id="g8qmo"></li>
switch config tool for configuring kernel mode switch phy driver in openwrt. uses generic netlink for kernel to use communication.
標簽： switch configuring generic openwrt
上傳時間： 2017-01-04
上傳用戶：妄想演繹師
CR6221 combines a dedicated current mode PWM controller with a high voltage power MOSFET. It is opti
上傳時間： 2013-04-24
上傳用戶：brucewan
CR6228 combines a dedicated current mode PWM controller with a high voltage power MOSFET. It is opti
上傳時間： 2013-05-17
上傳用戶：natopsi
Top switch ic
上傳時間： 2013-06-06
上傳用戶：eeworm
專輯類-開關電源相關專輯-119冊-749M Top-switch-ic-58頁-1.2M.pdf
標簽： Top-switch-ic 1.2 58
上傳時間： 2013-07-10
上傳用戶：jingfeng0192
implemention of FPGA and DSP linking port, using Asynchronous mode
標簽： implemention Asynchronous linking using
上傳時間： 2013-08-22
上傳用戶：fhjdliu
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上傳時間： 2013-11-23
上傳用戶：新手無憂
HT66F40使用SIM SPI Mode的用法 HT66F40 內建有串行接口功能，其中包括了SPI 和I2C 這兩種總線模式，本文以HT66F40為母體，介紹使用SPI 進行數據傳輸的方法和注意事項。
上傳時間： 2013-10-12
上傳用戶：tuilp1a
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上傳時間： 2014-11-22
上傳用戶：xcy122677
產品概述HP ProCurve Switch 2810系列包括兩款機型：帶有 20個10/100/1000端口的24端口HP ProCurve Switch 2810-24G和帶有44個10/100/1000端口的48端口HP ProCurve Switch 2810-48G。每款交換機還配有4個雙功能定制端口，可用于RJ-45 10/100/1000或mini-GBIC光纖千兆連接。2810系列交換機可提供出色的訪問安全性、高級優先化和流量監控能力，因而是高性能、安全10/100/1000連接的理想選擇。此外，它還價格經濟、簡單易用，帶有1U可堆疊外形，即使應用于更小的布線室內，也便于靈活操作。
上傳時間： 2013-11-24
上傳用戶：tiantwo
<strike id="wmaa4"></strike>