This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
標簽： Pulsoximeter Single-Chip Des
上傳時間： 2013-10-27
上傳用戶：黑漆漆
本文介紹了一種基于單片機的健身車轉速測量系統。該系統具有電路簡單、使用方便等特點。文中詳細介紹了該系統的工作原理,并且給出了它的硬件原理圖和軟件設計程序框圖。關鍵詞:轉速 單片機 測量ABSTRACT :This paper introduces a measuring system of the rotational velocity of exercise bike based on single - chip microcomputer . It has such advantages : simple circuit ,convenient use and so on. The work principle is presented in detail in this paper and the block diagram of hardware and program flow chart are giv2 en as well .KEYWORDS :Rotational velocity Single - chip microcomputer Measuring
上傳時間： 2013-11-02
上傳用戶：源弋弋
一種實用的微機自動配料秤系統:介紹一種由單片機構成的配料秤。敘述了秤的傳感器、變送器、信號的變換、硬件原理、軟件流程以及和DCS 系統構成的單回路調節系統,此系統可廣泛地應用于各行業的配料控制中。關鍵詞:配料秤 單片機 單回路調節系統 DCS 系統 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上傳時間： 2013-10-12
上傳用戶：zwei41
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上傳時間： 2014-04-03
上傳用戶：lizhizheng88
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上傳時間： 2013-11-10
上傳用戶：liaofamous
The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer with 8Kbytes of Flash programmable and erasable read only memory (PEROM). The deviceis manufactured using Atmel’s high-density nonvolatile memory technology and iscompatible with the industry-standard 80C51 and 80C52 instruction set and pinout.The on-chip Flash allows the program memory to be reprogrammed in-system or by aconventional nonvolatile memory programmer. By combining a versatile 8-bit CPUwith Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputerwhich provides a highly-flexible and cost-effective solution to many embedded controlapplications.
上傳時間： 2013-11-10
上傳用戶：1427796291
The C# program will display a mine field, plant mines, and provide hints on the number of mines around each grid. The player can therefore enjoy a typical Minesweeper game on a Smartphone.
標簽： mines program display provide
上傳時間： 2013-12-19
上傳用戶：xuanjie
Writing an interactive Java program with a graphical user interface (GUI) running on the Java phone emulator bundled with J2ME Wireless Toolkit 2.2 or Sun Java Wireless Toolkit 2.3 Beta Release. The Jave program will provide a tic-tac-toe board for two players to play a typical tic-tac-toe game on a Java mobile phone.
標簽： Java interactive graphical interface
上傳時間： 2014-01-22
上傳用戶：xuanjie
Writing an interactive Java program with a graphical user interface (GUI) running on the Java phone emulator bundled with J2ME Wireless Toolkit 2.2 or Sun Java Wireless Toolkit 2.3 Beta Release. The Jave program will provide a Gobang board for two players to play a typical Gobang game on a Java mobile phone.
標簽： Java interactive graphical interface
上傳時間： 2015-06-05
上傳用戶：LouieWu
