For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上傳時間： 2013-10-19
上傳用戶：royzhangsz
為了改變目前電網現場作業管理的變電巡檢、變電檢修試驗、輸電線路巡檢檢修等管理系統各自獨立運行，信息不能共享，功能、效率受限，建設和維護成本高的現狀，提出了采用B/S+C/S構架模式，將各現場作業管理模塊和生產MIS（管理系統）集成為一體的現場作業管理系統的設計方案，做到各子系統和生產MIS軟硬資源共享，做到同一數據唯一入口、一處錄入多處使用。各子系統設備人員等基礎信息來源于生產管理系統，各子系統又是生產管理系統的作業數據、缺陷信息的重要來源。經過研究試用成功和推廣應用，目前該系統已在江西電網220 kV及以上變電站全面應用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上傳時間： 2013-11-15
上傳用戶：han_zh
Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads controlled in time.
上傳時間： 2013-10-18
上傳用戶：如果你也聽說
下載后請修改文件擴展名為sch.體積和代碼都很小，集成電路(ic)全為貼片,祝各位有所啟發。 mcu:at89c4051 fm:tea5767 time:ds1302 temp:ds18b20
上傳時間： 2013-12-28
上傳用戶：xiaoyaa
HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
標簽： C8051F020
上傳時間： 2013-10-12
上傳用戶：lalalal
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
上傳時間： 2014-01-24
上傳用戶：xingisme
針對科研實驗中對拉壓千斤頂加載過程控制的需要，采用ATmega128單片機控制步進電機進而實現對執行系統的電動泵站實行自動控制。對力和位移的數據采集與處理及用步進電機控制電動泵站手柄的技術細節作了重點描述。通過單片機的A/D變換器對AMP放大模塊采集的電橋信號作量化處理，千斤頂的操控手柄位置依電動油泵閥門開啟的方向和大小作若干定位，單片機根據力或位移傳感器信號，實時控制步進電機驅動手柄旋轉到相應操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上傳時間： 2014-01-16
上傳用戶：hasan2015
為了提高傳統溫度控制系統的性能，將PID控制理論與嵌入式系統相結合，采用瑞薩電子公司的H8S/2166作為核心處理器，AD公司的AD7705以及熱敏電阻溫度傳感器作為溫度檢測單元，利用4×6小鍵盤、LCD顯示器和S1D13305液晶控制器達到良好的人機交互，設計出了一個應用于化工領域的嵌入式實時溫度控制系統。相比于傳統溫度控制系統，該系統提供了更強的計算能力和可擴展能力，采用增量PID控制算法實現復雜控制。通過實驗，該系統能達到0.1 ℃的溫度控制精度以及小于120 s的溫度穩定時間。 Abstract: In order to improve the performance of conventional temperature control system， combining PID control theory with embedded systems， using the Renesas Electronics Corp. H8S/2166 micro-controller as a core processors， AD7705 and thermistor temperature sensor as a temperature detection unit and 4×6 small keyboard， LCD and S1D13305 LCD controller as a good human-computer interaction， this paper designed an embedded real-time temperature control system which is applied in chemical industry. Compared with conventional temperature control system， this system provides more computing power and extensibility， and adopts PID control algorithm for complex control. Through the experiment， the system can reach temperature control accuracy of 0.1 ℃ and temperature stabilization time of less than 120 seconds.
上傳時間： 2014-12-26
上傳用戶：003030
目錄： 1. Character Type Functions － 字符類型函數 2. Standard C Input/Output Functions － 標準輸入輸出函數 3. Standard Library Functions － 標準庫和內存分配函數 4. Mathematical Functions － 數學函數 5. String Functions － 字符串函數 6. BCD Conversion Functions － BCD 轉換函數 7. Memory Access Functions － 存儲器訪問函數 8. Delay Functions － 延時函數 9. LCD Functions － LCD函數 10. LCD Functions for displays with 4x40 characters － 4×40 字符型LCD函數 11. LCD Functions for displays connected in 8 bit memory mapped mode －以8 位外部存儲 器模式接口的LCD顯示函數 12. I2C Bus Functions － I2C 總線函數 13. National Semiconductor LM75 Temperature Sensor Functions － LM75 溫度傳感器函數 14. Dallas Semiconductor DS1621 Thermometer/Thermostat Functions － DS1621 溫度計函 數 15. Philips PCF8563 Real Time Clock Functions － PCF8563 實時時鐘函數 16. Philips PCF8583 Real Time Clock Functions － PCF8583 實時時鐘函數 17. Dallas Semiconductor DS1302 Real Time Clock Functions － DS1302 實時時鐘函數 18. Dallas Semiconductor DS1307 Real Time Clock Functions － DS1307 實時時鐘函數 19. 1 Wire Protocol Functions － 單線通訊協議函數 20. Dallas Semiconductor DS1820/DS1822 Temperature Sensors Functions － DS1820/1822 溫度傳感器函數 21. SPI Functions － SPI 函數 22. Power Management Functions － 電源管理函數 23. Gray Code Conversion Functions － 格雷碼轉換函數
上傳時間： 2013-10-22
上傳用戶：歸海惜雪
針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上傳時間： 2013-10-10
上傳用戶：asdfasdfd
<li id="soqaq"></li>