產品型號：VK2C21A/B/C/D 產品品牌：VINKA/永嘉微/永嘉微電 封裝形式：SOP28/24/20/16 裸片:DICE（邦定COB）/COG（邦定玻璃用） 產品年份：新年份 聯 系 人：許碩 Q Q：191 888 5898 聯系手機：18898582398（信） 原廠直銷，工程服務，技術支持，價格最具優勢！QT459 VK2C21A/B/C/D概述： VK2C21是一個點陣式存儲映射的LCD驅動器，可支持最大80點（20SEGx4COM）或者最大128點（16SEGx8COM）的LCD屏。單片機可通過I2C接口配置顯示參數和讀寫顯示數據，也可通過指令進入省電模式。其高抗干擾，低功耗的特性適用于水電氣表以及工控儀表類產品。 特點： ★ 工作電壓 2.4-5.5V ★ 內置32 kHz RC振蕩器 ★ 偏置電壓（BIAS）可配置為1/3、1/4 ★ COM周期（DUTY）可配置為1/4、1/8 ★ 內置顯示RAM為20x4位、16x8位 ★ 幀頻可配置為80Hz、160Hz ★ 省電模式（通過關顯示和關振蕩器進入）
標簽： VK2C21 VK2C21A VK2C21B VK2C21C VK2C21D LCD抗干擾段碼屏驅動 段碼屏驅動抗干擾
上傳時間： 2022-06-09
上傳用戶：2937735731
描述了NTC使用B值計算出實際溫度與輸出的電壓之間的關系。
標簽： ntc計算
上傳時間： 2022-06-15
上傳用戶：
BC20-TE-B NB-Iot 評估板評估板原廠原理圖V1.2。完整對應實物裝置。
上傳時間： 2022-06-17
上傳用戶：
ASR M08-B設置軟件 V3.2 arduino 2560+ASRM08-B測試程序 arduino UNO+ASRM08-B測試程序語音控制臺燈電路圖及C51源碼(不帶校驗碼) 繼電器模塊設置。 ASR M08-B是一款語音識別模塊。首先對模塊添加一些關鍵字，對著該模塊說出關鍵字，串口會返回三位的數，如果是返回特定的三位數字，還會引起ASR M08-B的相關引腳電平的變化?！緶y試】①打開“ASR M08-B設置軟件 V3.2.exe”。②選擇“串口號”、“打開串口”、點選“十六進制顯示”。③將USB轉串口模塊連接到語音識別模塊上。接線方法如下：語音模塊TXD --> USB模塊RXD語音模塊RXD --> USB模塊TXD語音模塊GND --> USB模塊GND語音模塊3V3 --> USB模塊3V3（此端為3.3V電源供電端。）④將模塊的開關撥到“A”端，最好再按一次上面的大按鈕（按一次即可，為了確保模塊工作在正確的模式）。⑤對著模塊說“開燈”、“關燈”模塊會返回“0B”、“0A”，表示正常(注意：0B對應返回值010，0B對應返回值010，返回是16進制顯示的嘛，設置的時候是10進制設置的)。
標簽： ASR M08-B
上傳時間： 2022-07-06
上傳用戶：aben
視頻監控系統是一種先進的、防范能力強的綜合系統。它通過遙控攝像機及其輔助設備(鏡頭、云臺等)直接觀看被監控場所的一切情況，同時可以把監控場所的圖像內容傳送到監控中心，進行實時遠程監控。隨著計算機、網絡以及圖像處理、傳輸技術的迅猛發展，視頻監控技術也得到飛速發展，視頻監控進入了全數字化的網絡時代，傳統的模擬視頻監控系統和基于PC機的數字視頻監控系統已不能滿足現代社會發展的需要，基于嵌入式技術的網絡視頻監控系統成為視頻監控系統發展的新趨勢，具有廣闊的應用前景和實用價值。 本文在總結分析前人研究成果的基礎上，深入系統地研究了基于ARM和Linux的嵌入式系統開發技術，給出了基于ARM的嵌入式視頻服務器的總體設計方案和功能規劃，包括硬件結構和軟件結構，基于B/S(Browser/Server)服務機制的客戶端軟件設計大大降低了客戶端的軟硬件要求。然后，介紹了嵌入式Linux交叉編譯環境的搭建和嵌入式軟件的開發過程，通過BootLoader的配置燒寫和Linux內核的移植編譯，搭建了嵌入式視頻服務器運行開發的軟件平臺。最后詳細分析了嵌入式視頻服務器軟件部分各個功能模塊的設計思路及其關鍵代碼實現，用Liflux vide04linux APIs實現了視頻圖像的采集，視頻數據網絡傳輸采用了基于UDP協議的IP組播方式，而視頻圖像顯示模塊則采用了自行設計實現的基于IPicture COM接口的ActiveX控件，便于維護、更新和升級。 本文設計的基于ARM的嵌入式視頻服務器安裝設置方便，遠程客戶端用戶通過IE瀏覽器可直接訪問服務器，實時視頻圖像傳輸流暢，無明顯抖動，具有良好的穩定性、較高的性價比和一定的實用價值。
上傳時間： 2013-05-19
上傳用戶：彭玖華
介紹了基于51單片機的網絡連接控制器的軟硬件設計方案，主要采用Atmel公司的8 b單片機AT89C51作為核心處理器，采用RealTek公司的RTL8O19AS芯片接入以太網。同時討論了精簡的TCP／IP協議棧的分層次實現，實現了可靠的UDP數據通信。
上傳時間： 2013-11-22
上傳用戶：alex wang
The Kannel Open Source WAP and SMS gateway works as both an SMS gateway, for implementing keyword based services via GSM text messages, and a WAP gateway, via UDP. The SMS part is fairly mature, the WAP part is early in its development. In this release, the GET request for WML pages and WMLScript files via HTTP works, including compilation for WML and WMLScript to binary forms. Only the data call bearer (UDP) is supported, not SMS.
標簽： gateway implementing SMS keyword
上傳時間： 2014-01-11
上傳用戶：2525775
/* ********************************************************************************************************* * uC/TCP-IP V2 * The Embedded TCP/IP Suite * * (c) Copyright 2003-2010; Micrium, Inc.; Weston, FL * * All rights reserved. Protected by international copyright laws. * * uC/TCP-IP is provided in source form to registered licensees ONLY. It is * illegal to distribute this source code to any third party unless you receive * written permission by an authorized Micrium representative. Knowledge of * the source code may NOT be used to develop a similar product. * * Please help us continue to provide the Embedded community with the finest * software available. Your honesty is greatly appreciated. * * You can contact us at www.micrium.com. ********************************************************************************************************* */ /* ********************************************************************************************************* * * NETWORK TCP LAYER * (TRANSMISSION CONTROL PROTOCOL) * * Filename : net_tcp.h * Version : V2.10 * Programmer(s) : ITJ ********************************************************************************************************* * Note(s) : (1) Supports Transmission Control Protocol as described in RFC #793 with the following * restrictions/constraints : * * (a) TCP Security & Precedence NOT supported RFC # 793, Section 3.6 * * (b) TCP Urgent Data NOT supported RFC # 793, Section 3.7 * 'The Communication of * Urgent Information' * * (c) The following TCP options NOT supported : * * (1) Window Scale RFC #1072, Section 2 * RFC #1323, Section 2 * (2) Selective Acknowledgement (SACK) RFC #1072, Section 3 * RFC #2018 * RFC #2883 * (3) TCP Echo RFC #1072, Section 4 * (4) Timestamp RFC #1323, Section 3.2 * (5) Protection Against Wrapped Sequences (PAWS) RFC #1323, Section 4 * * (d) #### IP-Options-to-TCP-Connection RFC #1122, Section 4.2.3.8 * Handling NOT supported * * (e) #### ICMP-Error-Message-to-TCP-Connection RFC #1122, Section 4.2.3.9 * Handling NOT currently supported * * (2) TCP Layer assumes/requires Network Socket Layer (see 'net_sock.h MODULE Note #1a2'). ********************************************************************************************************* */ /*$PAGE*/ /* ********************************************************************************************************* * MODULE * * Note(s) : (1) TCP Layer module is NOT required for UDP-to-Application API configuration. * * See also 'net_cfg.h TRANSPORT LAYER CONFIGURATION' * & 'net_cfg.h USER DATAGRAM PROTOCOL LAYER CONFIGURATION'. * * See also 'net_tcp.h Note #2'. * * (2) The following TCP-module-present configuration value MUST be pre-#define'd in * 'net_cfg_net.h' PRIOR to all other network modules that require TCP Layer * configuration (see 'net_cfg_net.h TCP LAYER CONFIGURATION Note #2b') : * * NET_TCP_MODULE_PRESENT ********************************************************************************************************* */ #ifdef NET_TCP_MODULE_PRESENT /* See Note #2. */ /* ********************************************************************************************************* * EXTERNS ********************************************************************************************************* */ #if ((defined(NET_TCP_MODULE)) && \ (defined(NET_GLOBALS_EXT))) #define NET_TCP_EXT #else #define NET_TCP_EXT extern #endif /*$PAGE*/ /* ********************************************************************************************************* * DEFINES ********************************************************************************************************* */ /* ********************************************************************************************************* * TCP HEADER DEFINES * * Note(s) : (1) The following TCP value MUST be pre-#define'd in 'net_def.h' PRIOR to 'net_buf.h' so that * the Network Buffer Module can configure maximum buffer header size (see 'net_def.h TCP * LAYER DEFINES' & 'net_buf.h NETWORK BUFFER INDEX & SIZE DEFINES Note #1') : * * (a) NET_TCP_HDR_SIZE_MAX 60 (NET_TCP_HDR_LEN_MAX * * NET_TCP_HDR_LEN_WORD_SIZE) * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_LEN_MASK 0xF000u #define NET_TCP_HDR_LEN_SHIFT 12u #define NET_TCP_HDR_LEN_NONE 0u #define NET_TCP_HDR_LEN_MIN 5u #define NET_TCP_HDR_LEN_MAX 15u #define NET_TCP_HDR_LEN_WORD_SIZE CPU_WORD_SIZE_32 #define NET_TCP_HDR_SIZE_MIN (NET_TCP_HDR_LEN_MIN * NET_TCP_HDR_LEN_WORD_SIZE) #if 0 /* See Note #1a. */ #define NET_TCP_HDR_SIZE_MAX (NET_TCP_HDR_LEN_MAX * NET_TCP_HDR_LEN_WORD_SIZE) #endif #define NET_TCP_HDR_SIZE_TOT_MIN (NET_IP_HDR_SIZE_TOT_MIN + NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_SIZE_TOT_MAX (NET_IP_HDR_SIZE_TOT_MAX + NET_TCP_HDR_SIZE_MAX) #define NET_TCP_PSEUDO_HDR_SIZE 12u /* = sizeof(NET_TCP_PSEUDO_HDR) */ #define NET_TCP_PORT_NBR_RESERVED NET_PORT_NBR_RESERVED #define NET_TCP_PORT_NBR_NONE NET_TCP_PORT_NBR_RESERVED #define NET_TCP_HDR_URG_PTR_NONE 0x0000u /* See Note #2. */ /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER FLAG DEFINES * * Note(s) : (1) See 'TCP HEADER Note #2' for flag fields. * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_FLAG_MASK 0x0FFFu #define NET_TCP_HDR_FLAG_NONE DEF_BIT_NONE #define NET_TCP_HDR_FLAG_RESERVED 0x0FE0u /* MUST be '0'. */ #define NET_TCP_HDR_FLAG_URGENT DEF_BIT_05 /* See Note #2. */ #define NET_TCP_HDR_FLAG_ACK DEF_BIT_04 #define NET_TCP_HDR_FLAG_PUSH DEF_BIT_03 #define NET_TCP_HDR_FLAG_RESET DEF_BIT_02 #define NET_TCP_HDR_FLAG_SYNC DEF_BIT_01 #define NET_TCP_HDR_FLAG_FIN DEF_BIT_00 #define NET_TCP_HDR_FLAG_CLOSE NET_TCP_HDR_FLAG_FIN /* ********************************************************************************************************* * TCP FLAG DEFINES ********************************************************************************************************* */ /* ------------------ NET TCP FLAGS ------------------- */ #define NET_TCP_FLAG_NONE DEF_BIT_NONE #define NET_TCP_FLAG_USED DEF_BIT_00 /* TCP conn cur used; i.e. NOT in free TCP conn pool. */ /* ------------------ TCP TX FLAGS ------------------- */ /* TCP tx flags copied from TCP hdr flags. */ #define NET_TCP_FLAG_TX_FIN NET_TCP_HDR_FLAG_FIN #define NET_TCP_FLAG_TX_CLOSE NET_TCP_FLAG_TX_FIN #define NET_TCP_FLAG_TX_SYNC NET_TCP_HDR_FLAG_SYNC #define NET_TCP_FLAG_TX_RESET NET_TCP_HDR_FLAG_RESET #define NET_TCP_FLAG_TX_PUSH NET_TCP_HDR_FLAG_PUSH #define NET_TCP_FLAG_TX_ACK NET_TCP_HDR_FLAG_ACK #define NET_TCP_FLAG_TX_URGENT NET_TCP_HDR_FLAG_URGENT #define NET_TCP_FLAG_TX_BLOCK DEF_BIT_07 /* ------------------ TCP RX FLAGS ------------------- */ #define NET_TCP_FLAG_RX_DATA_PEEK DEF_BIT_08 #define NET_TCP_FLAG_RX_BLOCK DEF_BIT_15 /*$PAGE*/ /* ********************************************************************************************************* * TCP TYPE DEFINES * * Note(s) : (1) NET_TCP_TYPE_&&& #define values specifically chosen as ASCII representations of the TCP * types. Memory displays of TCP types will display with their chosen ASCII names. ********************************************************************************************************* */ /* ------------------ NET TCP TYPES ------------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x20504354u /* "TCP " in ASCII. */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x43542050u /* "TCP " in ASCII. */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #endif #endif /* ********************************************************************************************************* * TCP SEQUENCE NUMBER DEFINES * * Note(s) : (1) TCP initial transmit sequence number is incremented by a fixed value, preferably a large * prime value or a large value with multiple unique factors. * * (a) One reasonable TCP initial transmit sequence number increment value example : * * 65527 = 37 * 23 * 11 * 7 * * * #### NET_TCP_TX_SEQ_NBR_CTR_INC could be developer-configured in 'net_cfg.h'. * * See also 'NET_TCP_TX_GET_SEQ_NBR() Notes #1b2 & #1c2'. ********************************************************************************************************* */ #define NET_TCP_SEQ_NBR_NONE 0u #define NET_TCP_ACK_NBR_NONE NET_TCP_SEQ_NBR_NONE #define NET_TCP_TX_SEQ_NBR_CTR_INC 65527u /* See Note #1. */ #define NET_TCP_ACK_NBR_DUP_WIN_SIZE_SCALE 4 /*$PAGE*/ /* ********************************************************************************************************* * TCP DATA/TOTAL LENGTH DEFINES * * Note(s) : (1) (a) TCP total length #define's (NET_TCP_TOT_LEN) relate to the total size of a complete * TCP packet, including the packet's TCP header. Note that a complete TCP packet MAY * be fragmented in multiple Internet Protocol packets. * * (b) TCP data length #define's (NET_TCP_DATA_LEN) relate to the data size of a complete * TCP packet, equal to the total TCP packet length minus its TCP header size. Note * that a complete TCP packet MAY be fragmented in multiple Internet Protocol packets. ********************************************************************************************************* */ /* See Notes #1a & #1b. */ #define NET_TCP_DATA_LEN_MIN 0u #define NET_TCP_TOT_LEN_MIN (NET_TCP_HDR_SIZE_MIN + NET_TCP_DATA_LEN_MIN) #define NET_TCP_TOT_LEN_MAX (NET_IP_TOT_LEN_MAX - NET_IP_HDR_SIZE_MIN ) #define NET_TCP_DATA_LEN_MAX (NET_TCP_TOT_LEN_MAX - NET_TCP_HDR_SIZE_MIN) /*$PAGE*/ /* ********************************************************************************************************* * TCP SEGMENT SIZE DEFINES * * Note(s) : (1) (a) RFC # 879, Section 3 states that the TCP Maximum Segment Size "counts only * data octets in the segment, ... not the TCP header or the IP header". * * (b) RFC #1122, Section 4.2.2.6 requires that : * * (1) "The MSS value to be sent in an MSS option must be less than or equal to * * (A) MMS_R - 20 * * where MMS_R is the maximum size for a transport-layer message that can * be received." * * (2) "If an MSS option is not received at connection setup, TCP MUST assume a * default send MSS of 536 (576 - 40)." * * See also 'net_ip.h IP DATA/TOTAL LENGTH DEFINES Note #1'. ********************************************************************************************************* */ /* See Note #1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT (NET_IP_MAX_DATAGRAM_SIZE_DFLT - NET_IP_HDR_SIZE_MIN - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_MAX_SEG_SIZE_DFLT_RX NET_TCP_DATA_LEN_MAX /* See Note #1b1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT_TX NET_TCP_MAX_SEG_SIZE_DFLT /* See Note #1b2. */ #define NET_TCP_MAX_SEG_SIZE_NONE 0u #define NET_TCP_MAX_SEG_SIZE_MIN NET_TCP_MAX_SEG_SIZE_DFLT #define NET_TCP_MAX_SEG_SIZE_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_MIN NET_TCP_DATA_LEN_MIN #define NET_TCP_SEG_LEN_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_SYNC 1u #define NET_TCP_SEG_LEN_FIN 1u #define NET_TCP_SEG_LEN_CLOSE NET_TCP_SEG_LEN_FIN #define NET_TCP_SEG_LEN_ACK 0u #define NET_TCP_SEG_LEN_RESET 0u #define NET_TCP_SEG_LEN_PROBE 0u #define NET_TCP_DATA_LEN_TX_SYNC 0u #define NET_TCP_DATA_LEN_TX_FIN 0u #define NET_TCP_DATA_LEN_TX_CLOSE NET_TCP_DATA_LEN_TX_FIN #define NET_TCP_DATA_LEN_TX_ACK 0u #define NET_TCP_DATA_LEN_TX_PROBE_NO_DATA 0u #define NET_TCP_DATA_LEN_TX_PROBE_DATA 1u #define NET_TCP_DATA_LEN_TX_RESET 0u #define NET_TCP_TX_PROBE_DATA 0x00u /* ********************************************************************************************************* * TCP WINDOW SIZE DEFINES * * Note(s) : (1) Although NO RFC specifies the absolute minimum TCP connection window size value allowed, * RFC #793, Section 3.7 'Data Communication : Managing the Window' states that for "the * window ... there is an assumption that this is related to the currently available data * buffer space available for this connection". ********************************************************************************************************* */ #define NET_TCP_WIN_SIZE_NONE 0u #define NET_TCP_WIN_SIZE_MIN NET_TCP_MAX_SEG_SIZE_MIN #define NET_TCP_WIN_SIZE_MAX DEF_INT_16U_MAX_VAL /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER OPTIONS DEFINES * * Note(s) : (1) See the following RFC's for TCP options summary : * * (a) RFC # 793, Section 3.1 'Header Format : Options' * (b) RFC #1122; Sections 4.2.2.5, 4.2.2.6 * * (2) TCP option types are encoded in the first octet for each TCP option as follows : * * -------- * | TYPE | * -------- * * The TCP option type value determines the TCP option format : * * (a) The following TCP option types are single-octet TCP options -- i.e. the option type * octet is the ONLY octet for the TCP option. * * (1) TYPE = 0 End of Options List * (2) TYPE = 1 No Operation * * * (b) All other TCP options MUST be multi-octet TCP options (see RFC #1122, Section 4.2.2.5) : * * ------------------------------ * | TYPE | LEN | TCP OPT | * ------------------------------ * * where * TYPE Indicates the specific TCP option type * LEN Indicates the total TCP option length, in octets, including * the option type & the option length octets * TCP OPT Additional TCP option octets, if any, that contain the remaining * TCP option information * * The following TCP option types are multi-octet TCP options where the option's second * octet specify the total TCP option length, in octets, including the option type & the * option length octets : * * (1) TYPE = 2 Maximum Segment Size See RFC # 793, Section 3.1 'Header Format : * Options : Maximum Segment Size'; * RFC #1122, Section 4.2.2.6; * RFC # 879, Section 3 * * (2) TYPE = 3 Window Scale See 'net_tcp.h Note #1c1' * (3) TYPE = 4 SACK Allowed See 'net_tcp.h Note #1c2' * (4) TYPE = 5 SACK Option See 'net_tcp.h Note #1c2' * (5) TYPE = 6 Echo Request See 'net_tcp.h Note #1c3' * (6) TYPE = 7 Echo Reply See 'net_tcp.h Note #1c3' * (7) TYPE = 8 Timestamp See 'net_tcp.h Note #1c4' * * (3) TCP header allows for a maximum option list length of 40 octets : * * NET_TCP_HDR_OPT_SIZE_MAX = NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN * * = 60 - 20 * * = 40 * * (4) 'NET_TCP_OPT_SIZE' MUST be pre-defined PRIOR to all definitions that require TCP option * size data type. ********************************************************************************************************* */ /*$PAGE*/ #define NET_TCP_HDR_OPT_END_LIST 0u #define NET_TCP_HDR_OPT_NOP 1u #define NET_TCP_HDR_OPT_MAX_SEG_SIZE 2u #define NET_TCP_HDR_OPT_WIN_SCALE 3u #define NET_TCP_HDR_OPT_SACK_PERMIT 4u #define NET_TCP_HDR_OPT_SACK 5u #define NET_TCP_HDR_OPT_ECHO_REQ 6u #define NET_TCP_HDR_OPT_ECHO_REPLY 7u #define NET_TCP_HDR_OPT_TS 8u #define NET_TCP_HDR_OPT_PAD NET_TCP_HDR_OPT_END_LIST #define NET_TCP_HDR_OPT_LEN_END_LIST 1u #define NET_TCP_HDR_OPT_LEN_NOP 1u #define NET_TCP_HDR_OPT_LEN_MAX_SEG_SIZE 4u #define NET_TCP_HDR_OPT_LEN_WIN_SCALE 3u #define NET_TCP_HDR_OPT_LEN_SACK_PERMIT 2u #define NET_TCP_HDR_OPT_LEN_ECHO_REQ 6u #define NET_TCP_HDR_OPT_LEN_ECHO_REPLY 6u #define NET_TCP_HDR_OPT_LEN_TS 10u #define NET_TCP_HDR_OPT_LEN_SACK_MIN 6u #define NET_TCP_HDR_OPT_LEN_SACK_MAX 38u #define NET_TCP_HDR_OPT_LEN_MIN 1u #define NET_TCP_HDR_OPT_LEN_MIN_LEN 2u #define NET_TCP_HDR_OPT_LEN_MAX 38u typedef CPU_INT32U NET_TCP_OPT_SIZE; /* TCP opt size data type (see Note #4). */ #define NET_TCP_HDR_OPT_SIZE_WORD (sizeof(NET_TCP_OPT_SIZE)) #define NET_TCP_HDR_OPT_SIZE_MAX (NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_OPT_NBR_MIN 0u #define NET_TCP_HDR_OPT_NBR_MAX (NET_TCP_HDR_OPT_SIZE_MAX / NET_TCP_HDR_OPT_SIZE_WORD) #define NET_TCP_HDR_OPT_IX NET_TCP_HDR_SIZE_MIN /*$PAGE*/ /* ********************************************************************************************************* * TCP OPTION CONFIGURATION TYPE DEFINES * * Note(s) : (1) NET_TCP_OPT_CFG_TYPE_&&& #define values specifically chosen as ASCII representations of * the TCP option configuration types. Memory displays of TCP option configuration buffers * will display the TCP option configuration TYPEs with their chosen ASCII names. ********************************************************************************************************* */ /* ---------------- TCP OPT CFG TYPES ----------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_OPT_CFG_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x2053534Du /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x204E4957u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x504B4353u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x4B434153u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x51455245u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4F484345u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x20205354u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x534D2053u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x4957204Eu /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x4353504Bu /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x41534B43u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x52455145u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x43454F48u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x53542020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #endif #endif /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION TIMEOUT DEFINES * * Note(s) : (1) (a) (1) RFC #1122, Section 4.2.2.13 'DISCUSSION' states that "the graceful close algorithm * of TCP requires that the connection state remain defined on (at least) one end of * the connection, for a timeout period of 2xMSL ... During this period, the (remote * socket, local socket) pair that defines the connection is busy and cannot be reused". * * (2) The following sections reiterate that the TIME-WAIT state timeout scalar is two * maximum segment lifetimes (2 MSL) : * * (A) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check Sequence Number : TIME-WAIT STATE' * (B) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check FIN Bit : TIME-WAIT STATE' * * (b) (1) RFC #793, Section 3.3 'Sequence Numbers : Knowing When to Keep Quiet' states that * "the Maximum Segment Lifetime (MSL) is ... to be 2 minutes. This is an engineering * choice, and may be changed if experience indicates it is desirable to do so". * * (2) Microsoft Corporation's Windows XP defaults MSL to 15 seconds. ********************************************************************************************************* */ /* Max seg timeout (see Note #1b) : */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MIN_SEC ( 0u ) /* ... min = 0 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MAX_SEC ( 2u * DEF_TIME_NBR_SEC_PER_MIN) /* ... max = 2 minutes */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_DFLT_SEC ( 15u ) /* ... dflt = 15 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_SCALAR 2u /* ... scalar (see Note #1a). */ #define NET_TCP_CONN_TIMEOUT_CONN_DFLT_SEC (120u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt conn timeout = 120 minutes */ #define NET_TCP_CONN_TIMEOUT_USER_DFLT_SEC ( 30u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt user timeout = 30 minutes */ /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION STATES * * Note(s) : (1) See the following RFC's for TCP state machine summary : * * (a) RFC # 793; Sections 3.2, 3.4, 3.5, 3.9 * (b) RFC #1122; Sections 4.2.2.8, 4.2.2.10, 4.2.2.11, 4.2.2.13, 4.2.2.18, 4.2.2.20 * * (2) (a) #### Additional closing-data-available state used for closing connections to allow the * application layer to receive any remaining data. * * See also 'net_tcp.c NetTCP_RxPktConnHandlerFinWait1() Note #2f5A2', * 'net_tcp.c NetTCP_RxPktConnHandlerFinWait2() Note #2f5B', * 'net_tcp.c NetTCP_RxPktConnHandlerClosing() Note #2d2B2a1B', * & 'net_tcp.c NetTCP_RxPktConnHandlerLastAck() Note #2d2A1b'. ********************************************************************************************************* */ #define NET_TCP_CONN_STATE_NONE 0u #define NET_TCP_CONN_STATE_FREE 1u #define NET_TCP_CONN_STATE_CLOSED 10u #define NET_TCP_CONN_STATE_LISTEN 20u #define NET_TCP_CONN_STATE_SYNC_RXD 30u #define NET_TCP_CONN_STATE_SYNC_RXD_PASSIVE 31u #define NET_TCP_CONN_STATE_SYNC_RXD_ACTIVE 32u #define NET_TCP_CONN_STATE_SYNC_TXD 35u #define NET_TCP_CONN_STATE_CONN 40u #define NET_TCP_CONN_STATE_FIN_WAIT_1 50u #define NET_TCP_CONN_STATE_FIN_WAIT_2 51u #define NET_TCP_CONN_STATE_CLOSING 52u #define NET_TCP_CONN_STATE_TIME_WAIT 53u #define NET_TCP_CONN_STATE_CLOSE_WAIT 55u #define NET_TCP_CONN_STATE_LAST_ACK 56u #define NET_TCP_CONN_STATE_CLOSING_DATA_AVAIL 59u /* See Note #2a. */ /* ********************************************************************************************************* * TCP CONNECTION QUEUE STATES ********************************************************************************************************* */ #define NET_TCP_RX_Q_STATE_NONE 0u #define NET_TCP_RX_Q_STATE_CLOSED 100u #define NET_TCP_RX_Q_STATE_CLOSING 101u #define NET_TCP_RX_Q_STATE_SYNC 110u #define NET_TCP_RX_Q_STATE_CONN 111u #define NET_TCP_TX_Q_STATE_NONE 0u #define NET_TCP_TX_Q_STATE_CLOSED 200u #define NET_TCP_TX_Q_STATE_CLOSING 201u #define NET_TCP_TX_Q_STATE_SYNC 210u #define NET_TCP_TX_Q_STATE_CONN 211u #define NET_TCP_TX_Q_STATE_SUSPEND 215u #define NET_TCP_TX_Q_STATE_CLOSED_SUSPEND 220u #define NET_TCP_TX_Q_STATE_CLOSING_SUSPEND 221u /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION CODE DEFINES **************
上傳時間： 2015-11-22
上傳用戶：the same kong
近年來，隨著多媒體技術、計算機網絡與通信技術的的快速發展，傳統的監控系統也不斷向著新的發展方向進行著不斷的更新與發展。進而隨著嵌入式技術的出現以及人們對降低監控系統成本和提高可靠性的迫切需求，基于嵌入式系統的網絡視頻監控系統將成為新的研發熱點。 本文的目的是把嵌入式技術與計算機網絡技術相結合，構造一個性能穩定且具有較強處理能力的數字化遠程視頻監控系統。該監控系統以嵌入式Linux系統平臺作為服務器端，服務器程序在其上以后臺方式運行，等待監控系統環境中的客戶機使用瀏覽器向其發送訪問請求，實現在局域網乃至Internet網上對攝像頭的遠程控制。 文中把系統設計分為三大部分：系統硬件設計、嵌入式Linux在硬件平臺的實現和系統軟件設計。硬件設計部分首先提出了整個硬件系統的實現方案，接著詳細介紹了S3C2410處理器與存儲器、以太網控制器芯片以及USB和串口的接口電路設計；第二部分詳細敘述了嵌入式Linux在本系統硬件平臺的移植實現及應用程序的開發特點，重點講述了本系統平臺上Linux的引導加載程序Bootloader的設計過程；系統軟件部分首先介紹了USB接口攝像頭驅動在嵌入式Linux下的實現，重點講述了Video4Linux下視頻采集的實現，接著論述了如何實現圖像的JPEG壓縮，最后針對基于B/S模式的網絡通信系統結構，詳細闡述了網絡通信的具體實現過程和方法。 最后在辦公室局域網通過對系統測試，顯示了系統運行結果，實現了利用局域網或Internet網對遠程環境進行監控的功能。
上傳時間： 2013-07-04
上傳用戶：lgnf
永磁同步發電機由于一系列高效節能的優點，在工農業生產、航空航天、國防和日常生活中得到廣泛應用，并且受到許多學者的關注，其研究領域主要涉及永磁同步發電機的設計、精確性能分析、控制等方面。 本課題作為國家自然科學基金項目《無刷無勵磁機諧波勵磁的混合勵磁永磁電機的研究》的課題，主要研究永磁電機的電磁場空載和負載計算，求出永磁電機的電壓波形和電壓調整率，為分段式轉子的混合勵磁永磁電機的研究奠定基礎，主要做了以下工作： 首先介紹了永磁同步發電機的基本原理，包括永磁同步發電機的結構形式和永磁同步發電機的運行性能，采用傳統解析理論給出了電壓調整率的計算方法及外特性的計算模型；然后用有限元ANSYS對永磁同步發電機樣機進行實體建模，經過定義分配材料、劃分網格、加邊界條件和載荷、求解計算等，得到矢量磁位Az、磁場強度H、磁感應強度B等結果，直觀地看出電機內部的磁場分布情況。 其次根據電磁場計算結果，應用齒磁通法對其進行后處理。該方法求解轉子在一個齒距內不同位置處的磁場，以定子齒的磁通為計算單位，根據繞組與齒的匝鏈關系，計算出磁鏈隨時間的變化，進而得到永磁同步發電機空、負載時電壓大小及波形。通過計算結果寫實驗結果對比，驗證了齒磁通法的正確性，為計算永磁同步發電機各種性能特性提供有力工具。 最后，基于齒磁通法對永磁同步發電機的外特性進行了深入研究，定量分析了結構參數對外特性的影響規律，提出了有效降低電壓調整率的方法的是：增加氣隙長度g的同時，適當增加永磁體的磁化方向的長度hm；此外，要盡量的減少每相串聯匝數N和增大導線面積以減小阻抗參數。通過改變電機的結構參數，對其電磁場進行計算，找到永磁電機電壓調整率的變化規律，為加電勵磁的混合勵磁永磁電機做準備，達到穩定輸出電壓的目的。
上傳時間： 2013-04-24
上傳用戶：15853744528
