?? sdr_sdram.v
字號:
/******************************************************************************
*
* LOGIC CORE: SDR SDRAM Controller
* MODULE NAME: sdr_sdram()
* COMPANY: Northwest Logic, Inc.
* www.nwlogic.com
*
* REVISION HISTORY:
*
* Revision 1.0 05/11/2000 Description: Initial Release.
* 1.1 07/10/2000 Description: change precharge to terminate
* for full page accesses.
*
* FUNCTIONAL DESCRIPTION:
*
* This module is the top level module for the SDR SDRAM controller.
*
* Copyright Northwest Logic, Inc., 2000. All rights reserved.
******************************************************************************/
module sdr_sdram(
CLK,
RESET_N,
ADDR,
CMD,
CMDACK,
DATAIN,
DATAOUT,
DM,
SA,
BA,
CS_N,
CKE,
RAS_N,
CAS_N,
WE_N,
DQ,
DQM
);
`include "params.v"
input CLK; //System Clock
input RESET_N; //System Reset
input [`ASIZE-1:0] ADDR; //Address for controller requests
input [2:0] CMD; //Controller command
output CMDACK; //Controller command acknowledgement
input [`DSIZE-1:0] DATAIN; //Data input
output [`DSIZE-1:0] DATAOUT; //Data output
input [`DSIZE/8-1:0] DM; //Data mask input
output [11:0] SA; //SDRAM address output
output [1:0] BA; //SDRAM bank address
output [1:0] CS_N; //SDRAM Chip Selects
output CKE; //SDRAM clock enable
output RAS_N; //SDRAM Row address Strobe
output CAS_N; //SDRAM Column address Strobe
output WE_N; //SDRAM write enable
inout [`DSIZE-1:0] DQ; //SDRAM data bus
output [`DSIZE/8-1:0] DQM; //SDRAM data mask lines
reg [11:0] SA; //SDRAM address output
reg [1:0] BA; //SDRAM bank address
reg [1:0] CS_N; //SDRAM Chip Selects
reg CKE; //SDRAM clock enable
reg RAS_N; //SDRAM Row address Strobe
reg CAS_N; //SDRAM Column address Strobe
reg WE_N; //SDRAM write enable
reg [`DSIZE-1:0] DQIN;
wire [`DSIZE-1:0] DQOUT;
wire [`DSIZE-1:0] IDATAOUT; //Data output
reg [`DSIZE-1:0] DATAOUT; //Data output
wire [11:0] ISA; //SDRAM address output
wire [1:0] IBA; //SDRAM bank address
wire [1:0] ICS_N; //SDRAM Chip Selects
wire ICKE; //SDRAM clock enable
wire IRAS_N; //SDRAM Row address Strobe
wire ICAS_N; //SDRAM Column address Strobe
wire IWE_N; //SDRAM write enable
wire [`ASIZE-1:0] saddr;
wire [1:0] sc_cl;
wire [1:0] sc_rc;
wire [3:0] sc_rrd;
wire sc_pm;
wire [3:0] sc_bl;
wire load_mode;
wire nop;
wire reada;
wire writea;
wire refresh;
wire precharge;
wire oe;
wire CLK133;
wire CLK133B;
wire CLK;
pll1 PLL1(
.inclock(CLK),
.clock0(CLK133),
.clock1(CLK133B),
.locked(locked)
);
control_interface control1 (
.CLK(CLK133),
.RESET_N(RESET_N),
.CMD(CMD),
.ADDR(ADDR),
.REF_ACK(ref_ack),
.CM_ACK(cm_ack),
.NOP(nop),
.READA(reada),
.WRITEA(writea),
.REFRESH(refresh),
.PRECHARGE(precharge),
.LOAD_MODE(load_mode),
.SADDR(saddr),
.SC_CL(sc_cl),
.SC_RC(sc_rc),
.SC_RRD(sc_rrd),
.SC_PM(sc_pm),
.SC_BL(sc_bl),
.REF_REQ(ref_req),
.CMD_ACK(CMDACK)
);
command command1(
.CLK(CLK133),
.RESET_N(RESET_N),
.SADDR(saddr),
.NOP(nop),
.READA(reada),
.WRITEA(writea),
.REFRESH(refresh),
.PRECHARGE(precharge),
.LOAD_MODE(load_mode),
.SC_CL(sc_cl),
.SC_RC(sc_rc),
.SC_RRD(sc_rrd),
.SC_PM(sc_pm),
.SC_BL(sc_bl),
.REF_REQ(ref_req),
.REF_ACK(ref_ack),
.CM_ACK(cm_ack),
.OE(oe),
.SA(ISA),
.BA(IBA),
.CS_N(ICS_N),
.CKE(ICKE),
.RAS_N(IRAS_N),
.CAS_N(ICAS_N),
.WE_N(IWE_N)
);
sdr_data_path data_path1(
.CLK(CLK133),
.RESET_N(RESET_N),
.OE(oe),
.DATAIN(DATAIN),
.DM(DM),
.DATAOUT(IDATAOUT),
.DQIN(DQIN),
.DQOUT(DQOUT),
.DQM(DQM)
);
always @(posedge CLK133)
begin
SA <= ISA;
BA <= IBA;
CS_N <= ICS_N;
CKE <= ICKE;
RAS_N <= IRAS_N;
CAS_N <= ICAS_N;
WE_N <= IWE_N;
DQIN <= DQ;
DATAOUT <= IDATAOUT;
end
assign DQ = oe ? DQOUT : 32'bz;
endmodule
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -