LIBRARY IEEE;
USE IEEE.STD_LOGIC_1164.ALL;
ENTITY ADCINT IS
    PORT(D  : IN STD_LOGIC_VECTOR(7 DOWNTO 0);  --來自0809轉換好的8位數據
CLK  : IN STD_LOGIC;                          --狀態機工作時鐘
EOC  : IN STD_LOGIC;                  --轉換狀態指示，低電平表示正在轉換
ALE  : OUT STD_LOGIC;                 --8個模擬信號通道地址鎖存信號
START  : OUT STD_LOGIC;                 --轉換開始信號
OE  : OUT STD_LOGIC;                 --數據輸出3態控制信號
ADDA  : OUT STD_LOGIC;                --信號通道最低位控制信號
LOCK0  : OUT STD_LOGIC;               --觀察數據鎖存時鐘
Q  : OUT STD_LOGIC_VECTOR(7 DOWNTO 0)); --8位數據輸出
END ADCINT;
ARCHITECTURE behav OF ADCINT IS
TYPE states IS (st0, st1, st2, st3,st4) ; --定義各狀態子類型
  SIGNAL current_state, next_state: states :=st0 ;
  SIGNAL REGL 	    : STD_LOGIC_VECTOR(7 DOWNTO 0);
  SIGNAL LOCK	    : STD_LOGIC; -- 轉換后數據輸出鎖存時鐘信號
 BEGIN
ADDA <= '1';--當ADDA<='0'，模擬信號進入通道IN0；當ADDA<='1'，則進入通道IN1
Q <= REGL; LOCK0 <= LOCK ;
  COM: PROCESS(current_state,EOC)  BEGIN  --規定各狀態轉換方式
   CASE current_state IS           
   WHEN st0=>ALE<='0';START<='0';LOCK<='0';OE<='0';
        next_state <= st1; --0809初始化
   WHEN st1=>ALE<='1';START<='1';LOCK<='0';OE<='0';
next_state <= st2; --啟動采樣
   WHEN st2=> ALE<='0';START<='0';LOCK<='0';OE<='0';    
     IF (EOC='1') THEN next_state <= st3; --EOC=1表明轉換結束
	 ELSE next_state <= st2;  END IF ;    --轉換未結束，繼續等待
    
   WHEN st3=> ALE<='0';START<='0';LOCK<='0';OE<='1'; 
next_state <= st4;--開啟OE,輸出轉換好的數據
   WHEN st4=> ALE<='0';START<='0';LOCK<='1';OE<='1'; next_state <= st0;
   WHEN OTHERS => next_state <= st0;  
   END CASE ;
 END PROCESS COM ;
  REG: PROCESS (CLK)  
    BEGIN
     IF (CLK'EVENT AND CLK='1') THEN current_state<=next_state; END IF;
   END PROCESS REG ;      -- 由信號current_state將當前狀態值帶出此進程:REG
  LATCH1: PROCESS (LOCK) -- 此進程中，在LOCK的上升沿，將轉換好的數據鎖入
         BEGIN
        IF LOCK='1' AND LOCK'EVENT THEN   REGL <= D ; END IF;
       END PROCESS LATCH1 ; 
  END behav;