Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上傳時間： 2013-10-28
上傳用戶：hanbeidang
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上傳時間： 2013-11-09
上傳用戶：wweqas
Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上傳時間： 2013-11-23
上傳用戶：rocketrevenge
This application note is an overview discussion of theLinear Technology SPICE macromodel library. It assumeslittle if any prior knowledge of this software library or itshistory. However, it does assume familiarity with both theanalog simulation program SPICE (or one of its manyderivatives), and modern day op amps, including bipolar,JFET, and MOSFET amplifier technologies
上傳時間： 2013-11-14
上傳用戶：zhanditian
This publication represents the largest LTC commitmentto an application note to date. No other application noteabsorbed as much effort, took so long or cost so much.This level of activity is justified by our belief that high speedmonolithic amplifiers greatly interest users.
標簽： 高速放大器
上傳時間： 2014-01-07
上傳用戶：wfl_yy
This note describes some of the unique IC design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上傳時間： 2013-11-12
上傳用戶：671145514
Application considerations and circuits for the LT1001 and LT1002 single and dual precision amplifiers are illustrated in a number of circuits, including strain gauge signal conditioners, linearized platinum RTD circuits, an ultra precision dead zone circuit for motor servos and other examples.
上傳時間： 2013-10-18
上傳用戶：dreamboy36
噪聲系數(NF)是RF系統設計師常用的一個參數，它用于表征RF放大器、混頻器等器件的噪聲，并且被廣泛用作無線電接收機設計的一個工具。許多優秀的通信和接收機設計教材都對噪聲系數進行了詳細的說明(例如參考文獻1)，本文重點討論該參數在數據轉換器中的應用。
上傳時間： 2013-11-05
上傳用戶：李彥東
提出了一種應用于CSTN-LCD系統中低功耗、高轉換速率的跟隨器的實現方案。基于GSMC±9V的0.18 μm CMOS高壓工藝SPICE模型的仿真結果表明，在典型的轉角下，打開2個輔助模塊時，靜態功耗約為35 μA；關掉輔助模塊時，主放大器的靜態功耗為24 μA。有外接1 μF的大電容時，屏幕上的充放電時間為10 μs；沒有外接1μF的大電容時，屏幕上的充放電時間為13μs。驗證表明，該跟隨器能滿足CSTN-LCD系統低功耗、高轉換速率性能要求。
上傳時間： 2013-11-18
上傳用戶：kxyw404582151
針對科研實踐中需要采集大動態范圍模擬信號的問題，構建基于可變增益放大器8369的數字AGC系統。采用基于雙斜率濾波技術的設計，給出AGC控制算法的實現流程，利用Matlab仿真引入算例證明算法的可行性，并討論算法中關鍵參數取值對控制精度的影響。實際系統達到50dB動態范圍的設計目標。
上傳時間： 2013-12-22
上傳用戶：lx9076
