光伏發電是未來新能源發電重要方向之一，而光伏變流器是光伏發電系統的核心。介紹一種基于微網理念的光伏變流器設計。以該變流器為核心的光伏發電系統可以看做一個小型的微網系統。該系統能根據外部電網情況，工作于并網模式和離網模式。介紹了該系統的各個組成部件的設計以及變流器主電路部分器件的選型。最后，由實驗樣機進行測試。試驗結果驗證了電路拓?fù)浣Y(jié)構及控制方案的可行性，也說明了系統參數設計方法的正確性。
Abstract:
Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
鎖定放大是微弱信號檢測的重要手段。基于相關檢測理論，利用開關電容的開關實現鎖定放大器中乘法器的功能，提出開關電容和積分器相結合以實現相關檢測的方法，并設計出一種鎖定放大器。該鎖定放大器將微弱信號轉化為與之相關的方波，通過后續電路得到正比于被測信號的直流電平，為后續采集處理提供方便。測量數據表明鎖定放大器前級可將10-6 A的電流轉換為10-1 V的電壓，后級通過帶通濾波器級聯可將信號放大1×105倍。該方法在降低噪聲的同時，可對微弱信號進行放大，線性度較高、穩定性較好。
Abstract:
Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
Abstract: This application note describes how to build, debug, and run applications on the on-board MAXQ622microcontroller to interface with the DS8005 dual smart card interface. This is demonstrated in both IAREmbedded Workbench and the Rowley CrossWorks IDE, using sample code provided with the kit.
為了提高PCB板制作的效率，改變傳統的化學腐蝕制板工藝，使用機械仿形銑制作電路板的方法，設計了以ATMEGA16單片機為核心部件的PCB板雕刻機控制系統。其中包括PCB雕刻機的基本功能、主要硬件電路設計和軟件的實現流程，并給出了相關設計電路。重點分析了雕刻機步進電機的驅動電路以及主軸電機的驅動電路，該雕刻機經實際運行，系統工作良好，可有效提高PCB板的制作效率。
Abstract:
In order to improve the efficiency of production of PCB board and change the traditional chemical etching plates， using of mechanical copying milling method makes circuit boards，this paper introduces the PCB engraving machine control system used ATMEGA16 microcomputer as the core components. It includes basic function， the hardware circuit design and software realization process， and gives the corresponding circuit design.It analyses the drive circuit of engrawing machine stepper motor and spindle motor in detail. This engraving machine by practical operation， the system works well， which can effectively improve the production efficiency of PCB board.
數字控制的交流調速系統所選用的微處理器、功率器件及產生PWM波的方法是影響交流調速系統性能好壞的直接因素。在介紹了正弦脈寬調制(SPWM)技術的基礎上，設計了一種以8098單片機作為控制器，以智能功率模塊IPM為開關器件的變頻調速系統。通過軟件編程，產生正弦脈沖寬度調制波形來控制絕緣柵雙極晶體管的導通和關斷，從而達到控制異步電動機轉速的目的。實驗結果表明，該系統可調頻率調電壓，穩定度高，調速范圍寬，具有較強的實用價值
Abstract:
AC variable speed with digital control systems used microprocessors， power devices and generate PWM wave is the direct factors of affecting the performance AC speed regulation system. On the basis of introducing the sinusoidal pulse width modulation (SPWM) technology，this paper designed variable speed system which used 8098 as a controller， intelligent power module IPM as switching device. Through software programming， resulting in sinusoidal pulse width modulation waveform to control the insulated gate bipolar transistor turn on and off， so as to achieve the purpose of speed control of induction motors. Experimental results show that the system can adjust frequency modulation voltage， high stability， wide speed range， has a strong practical value.
利用單片機具有的智能程序控制的特點，設計了基于STC89C52單片機的"二極管特性測試器"，可對二極管一般特性進行快速測試。通過穩定線性電流源給二極管加載恒定電流，然后由高精度模數轉換器測試其壓降，以此為基礎可判斷二極管好壞、檢測二極管極性和測試二極管伏安特性等，避免了用萬用表測試只能測得極性而不知其特性這一缺點。可用于電子設計制作過程中對二極管進行快速測試，以確定被測二極管是否滿足電路的設計要求。
Abstract:
By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
為解決我國水位監測野外條件下長期無人看守的問題，研制開發了基于MSP430單片機的智能水位計。從其組成到各功能分別進行了詳細的介紹，該智能水位計不僅實現了水位數據的實時監測、記錄和定期采集等多種工作模式，而且提高了水位監測精度，實現了水位監測的智能化。
Abstract:
In order to solve the problems of long-term unmanned observation in the field water monitoring，an intelligence water-level meter based on MSP430 is developed composition and every function moduce of the water level meter was introduced in detail. It not only realizes water level data collection and storage， regularly gathering and so on， but also improves the water-level precision ， finally realizes the intelligence.
便攜式信號采集在機器健康診斷系統中有較高的應用價值。機器健康診斷的信號特點是包括低頻信號。本文研究是為了實現簡易而且低成本的低頻便攜式信號采集。以Microchip公司單片機PIC18F1320為核心設計信號采集電路，實現了信號的采集和保存。系統采用串行電可擦除芯片24LC32A保存數據，經過有線通信，信號數據由串行口通過MAX232芯片輸送到微型計算機接收和保存，最后繪制出信號波形。 微型計算機程序采用Visual Basic編程。研究成功采樣頻率為3 kHz的復雜信號，證明該方案符合設計要求。
Abstract:
Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
針對煤礦井下調度及緊急救援系統的需求，以DTMF編解碼模塊為核心，設計了具有自動撥號功能的新型電話系統。該系統利用MT8880對DTMF信號的編解碼功能實現一鍵撥號和遠程設置，通過檢測振鈴和忙音信號，完成自動摘機和掛機過程，配合AGC等外圍電路達到話音清晰流暢的效果。
Abstract:
To meet the demand for mine scheduling and emergency rescue system， with using DTMF signal codec as the core， a new telephone system was designed with automatic dialing function. In the system， the DTMF signal encoding and decoding function of MT8880 was used to achieve one-touch dialing and remote setting. The circuit detects the ringing and busy signal， and then completes automatic off-hook and hangup. With AGC(Automatic Gain Control) and other peripheral circuits， the voice was regulated to a clear and smooth effect.
