行為級仿真是提高流水線（Pipeline）ADC設計效率的重要手段。建立精確的行為級模型是進行行為級仿真的關鍵。本文采用基于電路宏模型技術的運算放大器模型，構建了流水線ADC的行為級模型并進行仿真。為驗證提出模型的精度，以一個7位流水線ADC為例，分別進行了電路級與行為級的仿真，并做了對比。結果表明這樣構建的行為級模型能較好地反映實際電路的特性，同時仿真時間大大縮短。
上傳時間： 2013-10-18
上傳用戶：zsjinju
Abstract: The DS4830 optical microcontroller's analog-to-digital converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
上傳時間： 2014-12-23
上傳用戶：萍水相逢
越柬越多的應用 例如過程控制、稱重等 都需要高分辨率、高集成度和低價格的ADC。 新型Σ ．△轉換技術恰好可以滿足這些要求 然而， 很多設計者對于這種轉換技術并不 分了解， 因而更愿意選用傳統的逐次比較ADC Σ．A轉換器中的模擬部分非常簡單(類似j 個Ibit ADC)， 而數字部分要復雜得多， 按照功能町劃分為數字濾波和抽取單元 由于更接近r 個數字器件，Σ △ADC的制造成本非常低廉.
標簽： ADC
上傳時間： 2013-10-24
上傳用戶：han_zh
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上傳時間： 2013-11-13
上傳用戶：ca05991270
Abstract: This article discusses application circuits for Maxim force/sense digital-to-analog converters (DACs). Applications include:selectable fixed-gain DAC, programmable gain DAC, photodiode bias control, amperometric sensor control, digitally programmablecurrent source, Kelvin load sensing, temperature sensing, and high current DAC output. A brief description of the various DAC outputconfigurations is also given.
標簽： DAC
上傳時間： 2013-11-04
上傳用戶：youmo81
將模擬信號轉換為數字信號后再進行處理,是當前信號處理普遍使用的方法,模數轉換器（ADC）就是將模擬信號轉換為數字信號的器件,所以計算其有效轉換位數對系統性能評估就顯得尤為重要。文中結合項目工程實踐,討論了ADC有效轉換位數的兩種測試方法:噪聲測試法和信噪比測試法,并對兩種方法進行了仿真與分析。
上傳時間： 2013-12-17
上傳用戶：1184599859
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上傳時間： 2013-10-17
上傳用戶：sjb555
交調失真(IMD)是用于衡量放大器、增益模塊、混頻器和其他射頻元件線性度的一項常用指標。二階和三階交調截點(IP2和IP3)是這些規格參數的品質因素，以其為基礎可以計算不同信號幅度下的失真積。雖然射頻工程師們非常熟悉這些規格參數，但當將其用于ADC時往往會產生一些困惑。本教程首先在ADC的框架下對交調失真進行定義，然后指出將IP2和IP3的定義應用于ADC時必須采取的一些預防措施。
上傳時間： 2014-01-07
上傳用戶：歸海惜雪
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
上傳時間： 2013-11-02
上傳用戶：ywcftc277
Digital-to-analog converters (DACs) are prevalent inindustrial control and automated test applications.General-purpose automated test equipment often requiresmany channels of precisely controlled voltagesthat span several voltage ranges. The LTC2704 is ahighly integrated 16-bit, 4-channel DAC for high-endapplications. It has a wide range of features designed toincrease performance and simplify design.
上傳時間： 2013-11-22
上傳用戶：元宵漢堡包
