FEATURES
Unique 1-Wire interface requires only one port pin for communication
Multidrop capability simplifies distributed temperature sensing applications
Requires no external components
Can be powered from data line. Power supply range is 3.0V to 5.5V
Zero standby power required
Measures temperatures from -55°C to +125°C. Fahrenheit equivalent is -67°F to +257°F
±0.5°C accuracy from -10°C to +85°C
Thermometer resolution is programmable from 9 to 12 bits
Converts 12-bit temperature to digital word in 750 ms (max.)
User-definable, nonvolatile temperature alarm settings
Alarm search command identifies and addresses devices whose temperature is outside of programmed limits (temperature
alarm condition)
Applications include thermostatic controls, industrial systems, consumer products,
thermometers, or any thermally sensitive system
High input impedance and a wide input range are twohighly desirable features in a precision ANALOG-TO-DIGITALconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
利用單片機具有的智能程序控制的特點，設計了基于STC89C52單片機的"二極管特性測試器"，可對二極管一般特性進行快速測試。通過穩定線性電流源給二極管加載恒定電流，然后由高精度模數轉換器測試其壓降，以此為基礎可判斷二極管好壞、檢測二極管極性和測試二極管伏安特性等，避免了用萬用表測試只能測得極性而不知其特性這一缺點。可用于電子設計制作過程中對二極管進行快速測試，以確定被測二極管是否滿足電路的設計要求。
Abstract:
By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
msp430The LDC1312 and LDC1314 are 2- and 4-channel,
1? Easy-to-use – minimal configuration required
12-bit inductance to digital converters (LDCs) for
? Measure up to 4 sensors with one IC
inductive sensing solutions. With multiple channels ? Multiple channels support environmental and and support for remote sensing, the LDC1312 and aging compensation LDC1314 enable the performance and reliability benefits of inductive sensing to be realized at minimal? Multi-channel remote sensing provides lowest cost and power. The products are easy to use, onlysystem cost requiring that the sensor frequency be within 1 kHz ? Pin-compatible medium and high-resolution and 10 MHz to begin sensing. The wide 1 kHz to 10 options MHz sensor frequency range also enables use of very small PCB coils, further reducing sensing– LDC1312/4: 2/4-ch 12-bit LDC solution cost and size.– LDC1612/4: 2/4-ch 28
T
his book covers basic communications theory and practical imple-
mentation of transmitters and receivers. In so doing, I focus on dig-
ital modulation, demodulation methods, probabilities, detection of
digital signals, and spread spectrum system design and analysis. This book
was written for those who want a good understanding of the basic prin-
ciples of digital wireless communication systems, including spread spec-
trum techniques. This book also provides a good intuitive and practical
approach to digital communications. Therefore it is a valuable resource for
anyoneinvolvedinwirelesscommunicationsandtransceiverdesignfordig-
ital communications. The reader will gain a broad understanding of basic
communication principles for transceiver design, digital communications,
and spread spectrum, along with examples of many types of commercial
and military data link systems.
