在研究傳統家用燃氣報警器的基礎上，以ZigBee協議為平臺，構建mesh網狀網絡實現網絡化的智能語音報警系統。由于傳感器本身的溫度和實際環境溫度的影響，傳感器標定后采用軟件補償方法。為了減少系統費用，前端節點采用半功能節點設備，路由器和協調器采用全功能節點設備，構建mesh網絡所形成的家庭內部報警系統，通過通用的電話接口連接到外部的公用電話網絡，啟動語音模塊進行報警。實驗結果表明，在2.4 GHz頻率下傳輸，有墻等障礙物的情況下，節點的傳輸距離大約為35 m，能夠滿足家庭需要，且系統工作穩定，但在功耗方面仍需進一步改善。
Abstract:
On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligent voice alarm system. Because of the sensor temperature and the actual environment temperature, this system design used software compensation after calibrating sensor. In order to reduce system cost, semi-functional node devices were used as front-end node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in case of walls and other obstacles by 2.4GHz frequency transmission, this is able to meet family needs and work steadily, but still needs further improvement in power consumption.
闡述了軌道交通列車定位技術。介紹了在軌道交通系統中列車定位技術的功能，國內外軌道交通中主要采用的列車定位方法，重點論述了幾種主要定位技術，并從定位精度、閉塞制式、維護投資成本、抗干擾等方面進行分析比較。提出目前軌道交通定位技術應綜合運用，取長補短，多種方法相互融合，才能滿足軌道交通中對安全可靠性的要求。
Abstract:
Rail train positioning technology is described. The paper introduces the funetions of the train positioning technology in the rail transit system， the main methods of train positioning do mestic and international rail， and focuses on several key methods， analyzes and compares from the positioning accuracy， block system, maintenance and investment cost， interference and so on， suggested that the current rail positioning technology should be integrated use of positioning method of meriging， learn from each other， to meet the reliability requirements of rail safety.
針對UHF讀寫器設計中，在符合EPC Gen2標準的情況下，對標簽返回的高速數據進行正確解碼以達到正確讀取標簽的要求，提出了一種新的在ARM平臺下采用邊沿捕獲統計定時器數判斷數據的方法，并對FM0編碼進行解碼。與傳統的使用定時器定時采樣高低電平的FM0解碼方法相比，該解碼方法可以減少定時器定時誤差累積的影響；可以將捕獲定時器數中斷與數據判斷解碼相對分隔開，使得中斷對解碼影響很小，實現捕獲與解碼的同步。通過實驗表明，這種方法提高了解碼的效率，在160 Kb/s的接收速度下，讀取一張標簽的時間約為30次/s。
Abstract:
Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
通過比較各種隔離數字通信的特點和應用范圍，指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口，有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路，說明設計過程中的注意事項，對光收發模塊的電壓特性和頻率特性進行全面試驗，并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明，該設計可為電力現場、電力電子及儀器儀表的設計提供參考。
Abstract:
y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
同步技術是跳頻通信系統的關鍵技術之一，尤其是在快速跳頻通信系統中，常規跳頻通信通過同步字頭攜帶相關碼的方法來實現同步，但對于快跳頻來說，由于是一跳或者多跳傳輸一個調制符號，難以攜帶相關碼。對此引入雙跳頻圖案方法，提出了一種適用于快速跳頻通信系統的同步方案。采用短碼攜帶同步信息，克服了快速跳頻難以攜帶相關碼的困難。分析了同步性能，仿真結果表明該方案同步時間短、虛警概率低、捕獲概率高，同步性能可靠。
Abstract:
Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
提出了一種以ARM微處理器為控制核心的遠程無線視頻監控終端的設計方案，其監控終端的硬件設計包括視頻采集處理、中央管理控制、無線傳輸3個模塊。并給出了監控終端的軟件開發平臺和開發模式的系統啟動代碼、嵌入式Linux系統移植以及驅動程序和應用程序。測試結果表明，該監控終端設計方案合理、有效，基本滿足監控需求。
Abstract:
A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。
Abstract:
To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of
Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
