針對使用硬件描述語言進行設計存在的問題，提出一種基于FPGA并采用DSP Builder作為設計工具的數字信號處理器設計方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ設計流程，設計了一個12階FIR 低通數字濾波器，通過Quartus 時序仿真及嵌入式邏輯分析儀SignalTapⅡ硬件測試對設計進行了驗證。結果表明，所設計的FIR 濾波器功能正確，性能良好。
Abstract:
Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order low-pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
為了擴大監控范圍，提高資源利用率，降低系統成本，提出了一種多通道視頻切換的解決方案。首先從視頻信號分離出行場信號，然后根據行場信號由DSP和FPGA產生控制信號，控制多路視頻通道之間的切換，從而實現讓一個視頻處理器同時監控不同場景。實驗結果表明，該方案可以在視頻監控告警系統中穩定、可靠地實現視頻通道的切換。
Abstract:
To expand the scope of monitoring， improve resource utilization， reduce system cost， a multiple video channels signal switching method is pointed out in this paper. First， horizontal sync signal and field sync signal from the video signal are separated， then control signal according to the sync signal by DSP and FPGA is generated to control the switching between multiple video channels. Thus， it achieves to make a video processor to monitor different place. Experimental results show that the method can realize video channel switching reliably， and is applied in the video monitoring warning system successfully.
在綜合分析諧波勵磁無刷同步發電機勵磁控制系統的基礎上,對其勵磁控制策略進行了研究,開發了一套基于DSP( TMS320F2812) 控制的新型柴油發電機勵磁控制系統,該系統采用參數自適應模糊PID 控制勵磁,選用交流采樣方式實時檢測各信號的瞬時特性,系統仿真結果以及在1 臺25 kW 工頻柴油發電機上的試驗結果證明了該控制器具有較好的電壓調節特性,系統穩態和暫態性能完全滿足發電機對勵磁系統的要求。關鍵詞:勵磁調節;模糊PID 控制;數字信號處理器;交流采樣
Abstract :According to the general analysis of the excitation cont rol system of the harmonious wave excitation brushless synchronous generator and it s characteristics ,a new type of diesel generator excitation cont rol system based on DSP( TMS320F2812) was designed. An adaptive fuzzy PID cont rol of excitation is used in this system. To detect the t ransient characteristics of the signals in a timely manner ,AC sampling was applied.The system simulation result s and the testing result s f rom a 25 kW diesel generator (50 Hz) can prove that the voltage regulation characteristics of the excitation cont rol system are very well ,and both the steadyOstate performance and the t ransient performance of the generator are also good.Key words :excitation cont rol ;fuzzy PID cont rol ;digital signal processor (DSP) ;AC sampling
摘 要 瞬態仿真領域的許多工作需要獲得可視化數據, 仿真電路不能將輸出參數繪制成圖形時研究工作將受到很大影響. 而權威電路仿真軟件PSpice 在這個方面不盡如人意. 本文提出了一種有效的解決辦法: 通過MATLAB 編程搭建一個PSpice 與MATLAB 的數據接口,使PSpice輸出數據文件可以導入到MATLAB中繪制圖形. 這令我們能夠很方便地獲得數據的規律以有效地分析仿真結果, 這項技術對于教學和工程實踐都有比較實際的幫助.關鍵詞: 瞬態仿真 仿真程序 PSpice MATLAB 可視化數據The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of transient simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interfaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the field of education.Keywords Transient Simulation Emulator PSpice MATLAB Viewdata1 引言科學研究和工程應用常需要進行電路仿真 PSpice可進行直流 交流 瞬態等基本電路特性分析 也可進行蒙托卡諾 MC 統計分析 最壞情況 Wcase 分析 優化設計等復雜電路特性分析 它是國際上仿真電路的權威軟件 而MATLAB的主要特點有 高效方便的矩陣和數組運算 編程效率高 結構化面向對象 方便的繪圖功能 用戶使用方便 工具箱功能強大 兩者各有著重點 兩種軟件結合應用 對研究工作有很重要的意義香港理工大學Y. S. LEE 等人首先將PSpice和MATLAB結合 開發了電力電子電路優化用的CAD 程序MATSPICE[6] 將兩者相結合的關鍵在于 如何用MATLAB 獲取PSpice的仿真數據 對此參考文獻 6 里沒有詳細敘述 本文著重說明用MATLAB 讀取PSpice仿真數據的具體方法本論文利用MATLAB對PSpice仿真出的數據處理繪制出后者無法得到或是效果不好的仿真圖形 下面就兩者結合使用的例子 進行具體說明
Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。
Abstract:
To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
Abstract: The application note addresses how G3-PLC, a powerline communications protocol approvedby the International Telecommunications Union (ITU), enables mesh networking in advanced metering
Abstract: Standard PCB design and mounting processes can adversely influence MEMS inertial sensors.This application note contains guidelines for the layout, soldering, and mounting of MEMS inertialsensors in LGA packages in order to reduce stresses and improve functionality.
Abstract: Communication with 1-Wire slave devices requires a 1-Wire master. There are numerous ways to build a 1-Wire master (see reference design 4206, "Choosing the Right 1-Wire Master for Embedded Applications"). Thisdocument describes the DS1WM, a synthesizable 1-Wire master that can be implemented in an application-specificintegrated circuit (ASIC) or field-programmable gate array (FPGA).
