磁芯電感器的諧波失真分析 摘 要：簡述了改進鐵氧體軟磁材料比損耗系數和磁滯常數ηB，從而降低總諧波失真THD的歷史過程，分析了諸多因數對諧波測量的影響，提出了磁心性能的調控方向。 關鍵詞：比損耗系數， 磁滯常數ηB ，直流偏置特性DC-Bias，總諧波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient，hysteresis constant，DC-Bias，THD 近年來，變壓器生產廠家和軟磁鐵氧體生產廠家，在電感器和變壓器產品的總諧波失真指標控制上，進行了深入的探討和廣泛的合作，逐步弄清了一些似是而非的問題。從工藝技術上采取了不少有效措施，促進了質量問題的迅速解決。本文將就此熱門話題作一些粗淺探討。 一、 歷史回顧 總諧波失真（Total harmonic distortion） ，簡稱THD，并不是什么新的概念，早在幾十年前的載波通信技術中就已有嚴格要求<1>。1978年郵電部公布的標準YD/Z17－78“載波用鐵氧體罐形磁心”中，規定了高μQ材料制作的無中心柱配對罐形磁心詳細的測試電路和方法。如圖一電路所示，利用LC組成的150KHz低通濾波器在高電平輸入的情況下測量磁心產生的非線性失真。這種相對比較的實用方法，專用于無中心柱配對罐形磁心的諧波衰耗測試。 這種磁心主要用于載波電報、電話設備的遙測振蕩器和線路放大器系統，其非線性失真有很嚴格的要求。
圖中 ZD —— QF867 型阻容式載頻振蕩器，輸出阻抗 150Ω， Ld47 —— 47KHz 低通濾波器，阻抗 150Ω，阻帶衰耗大于61dB， Lg88 ——并聯高低通濾波器，阻抗 150Ω，三次諧波衰耗大于61dB Ld88 ——并聯高低通濾波器，阻抗 150Ω，三次諧波衰耗大于61dB FD —— 30～50KHz 放大器， 阻抗 150Ω， 增益不小于 43 dB，三次諧波衰耗b3(0)≥91 dB, DP —— Qp373 選頻電平表，輸入高阻抗， L ——被測無心罐形磁心及線圈， C ——聚苯乙烯薄膜電容器CMO-100V-707APF±0.5%,二只。
測量時，所配用線圈應用絲包銅電磁線SQJ9×0.12(JB661-75)在直徑為16.1mm的線架上繞制 120 匝， （線架為一格） ， 其空心電感值為 318μH（誤差1％） 被測磁心配對安裝好后，先調節振蕩器頻率為 36.6～40KHz， 使輸出電平值為+17.4 dB， 即選頻表在 22′端子測得的主波電平 （P2）為+17.4 dB，然后在33′端子處測得輸出的三次諧波電平（P3）， 則三次諧波衰耗值為：b3(+2)= P2+S+ P3 式中：S 為放大器增益dB 從以往的資料引證， 就可以發現諧波失真的測量是一項很精細的工作，其中測量系統的高、低通濾波器，信號源和放大器本身的三次諧波衰耗控制很嚴，阻抗必須匹配，薄膜電容器的非線性也有相應要求。濾波器的電感全由不帶任何磁介質的大空心線圈繞成，以保證本身的“潔凈” ，不至于造成對磁心分選的誤判。 為了滿足多路通信整機的小型化和穩定性要求， 必須生產低損耗高穩定磁心。上世紀 70 年代初，1409 所和四機部、郵電部各廠，從工藝上改變了推板空氣窯燒結，出窯后經真空罐冷卻的落后方式，改用真空爐，并控制燒結、冷卻氣氛。技術上采用共沉淀法攻關試制出了μQ乘積 60 萬和 100 萬的低損耗高穩定材料，在此基礎上，還實現了高μ7000～10000材料的突破，從而大大縮短了與國外企業的技術差異。當時正處于通信技術由FDM（頻率劃分調制）向PCM（脈沖編碼調制） 轉換時期， 日本人明石雅夫發表了μQ乘積125 萬為 0.8×10 ，100KHz）的超優鐵氧體材料<3>，其磁滯系數降為優鐵
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of
Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
Abstract: As industrial control systems (ICSs) have become increasingly connected and use more off-the-shelfcomponents, new vulnerabilities to cyber attacks have emerged. This tutorial looks at three types of ICSs:programmable logic controllers (PLCs), supervisory control and data acquisition (SCADA) systems, anddistributed control systems (DCSs), and then discusses security issues and remedies. This document alsoexplains the benefits and limitations of two cryptographic solutions (digital signatures and encryption) andelaborates on the reasons for using security ICs in an ICS to support cryptography.
為了提高直接轉矩控制（DTC）系統定子磁鏈估計精度，降低電流、電壓測量的隨機誤差，提出了一種基于擴展卡爾曼濾波（EKF）實現異步電機轉子位置和速度估計的方法。擴展卡爾曼濾波器是建立在基于旋轉坐標系下由定子電流、電壓、轉子轉速和其它電機參量所構成的電機模型上，將定子電流、定子磁鏈、轉速和轉子角位置作為狀態變量，定子電壓為輸入變量，定子電流為輸出變量，通過對磁鏈和轉速的閉環控制提高定子磁鏈的估計精度，實現了異步電機的無速度傳感器直接轉矩控制策略，仿真結果驗證了該方法的可行性,提高了直接轉矩的控制性能。
Abstract:
In order to improve the Direct Torque Control（DTC） system of stator flux estimation accuracy and reduce the current， voltage measurement of random error， a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters （state vector: stator current， stator flux linkage， rotor angular speed and position； input: stator voltage； output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The simulation results show it is efficient and improves the control performance.
Abstract: This application note presents an overview of electronic margining and its value in detectingpotential system failures before a product ships from the factory. It is a calibration method that effectivelypredicts and allows adjustments to improve product quality. Margining also can be used to sort productsinto performance levels, allowing premium products to be sold at premium prices. We discuss thedownside of sorting and suggest alternative ways to segregate products.
Abstract: This application note discusses the REF pin functionality in the indirect current-feedbackarchitecture for instrumentation amplifiers. This article compares the importance of a REF buffer in a
Abstract: Many modern industrial, medical, and commercial applications require temperature measurements in the extended temperature rangewith accuracies of ±0.3°C or better, performed with reasonable cost and often with low power consumption. This article explains how platinumresistance temperature detectors (PRTDs) can perform measurements over wide temperature ranges of -200°C to +850°C, with absolute accuracyand repeatability better than ±0.3°C, when used with modern processors capable of resolving nonlinear mathematical equation quickly and costeffectively. This article is the second installment of a series on PRTDs. For the first installment, please read application note 4875, "High-Accuracy Temperature Measurements Call for Platinum Resistance Temperature Detectors (PRTDs) and Precision Delta-Sigma ADCs."
Abstract: This application note explains how to design an intelligent lighting controller that senses and measures the ambient lightlevel with an ambient light sensor (ALS). Equipped with a real-time clock (RTC), the controller also knows when to turn lighting on oroff at specified times. The system presented in this document can be used to control all luminaires that are mains-supply operated.Controller software is also provided in hex format.
基于通用集成運算放大器，利用MASON公式設計了一個多功能二階通用濾波器，能同時或分別實現低通、高通和帶通濾波，也能設計成一個正交振蕩器。電路的極點頻率和品質因數能夠獨立、精確地調節。電路使用4個集成運放、2個電容和11個電阻，所有集成運放的反相端虛地。利用計算機仿真電路的通用濾波功能、極點頻率和品質因數的獨立控制和正交正弦振蕩，從而證明該濾波器正確有效。
Abstract:
A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。
Abstract:
Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
