設計一種基于AT89C52的語音錄放系統，利用單片機、ISD2560語音錄放器件、麥克風、揚聲器等元器件實現硬件電路的設計，并利用C51高級語言設計ISD2560器件控制字的寫入和定時中斷程序。經軟硬件調試，結果表明該系統錄放效果良好，具有一定的工程實用價值。
Abstract:
Voice recording and playback system based on AT89C52is designed in this paper.Using the single-chip microcomputer，voice recording and playback chip ISD2560，microphone and speaker to realize the hardware circuit design.Writing ISD2560control words and timing interrupt procedures are designed by C51advanced language.Through the hardware and software test,voice recording and playback system play better voice,and this system has some engineering practical values.
針對盤山路存在的轉彎盲區，即在轉彎時司機無法得知彎路對面是否有車輛通過，設計一種基于C8051F310的山路轉彎預防警示系統。該系統利用一階濾波算法檢測山路轉彎時是否有車輛通過。運用該算法可增強系統檢測的實時性，提高檢測機動車輛的靈敏度，同時大大減少環境溫度對檢測的干擾。試驗表明該系統能夠正確指示出在山路轉彎時是否有車輛通過，目前該系統已安裝在盤山路上，可大大減少事故的發生率。
Abstract:
Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
介紹一種基于CAN總線的牽引變電站自動化系統通訊規約的設計，CAN通訊規約采用標準幀，報文采用主動發送和發送查詢兩種處理形式。該設計在城市輕軌與地鐵牽引變電站中的應用表明：可實現間隔層和通訊處理層的數據快速、可靠的交換，提高牽引變電站的安全性和穩定性
。
Abstract:
This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
介紹了以AVR單片機ATmega16為核心，采用前端信號調理電路、程控增益放大器以及波形顯示LCD（GDM12864A）實現的一個簡易示波器。并給出該系統設計的硬件和軟件設計方案。
Abstract:
Abstract:This paper introduces an easy digital storage oscilloscope based on the AVR microcontroller ATmega16,especially emphasizes on the software design and the hardware design which contains signal processing circuit,gain-programmed amplifier circuit and LCD’s interface circuit and so on.
以89S52單片機和EP1C6Q240C8型FPGA為控制核心的多功能計數器，是由峰值檢波、A/D轉換、程控放大、比較整形、移相網絡部分組成,可實現測量正弦信號的頻率、周期和相位差的功能。多功能計數器采用等精度的測量方法，可實現頻率為1Hz～10MHz、幅度為0.01～5Vrms的正弦信號的精確測頻，以及頻率為10Hz～100kHz、幅度為0.5～5Vrms的正弦信號精確測相。液晶顯示器能夠實時顯示當前信號的頻率、周期和相位差。該多功能計數器精度高，界面友好，實用性強。
Abstract:
A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
介紹了當前普通標記機控制系統現狀及其存在缺點，給出氣動標記機及相頻修正PWM模式的工作原理。采用ATmega16單片機和USB轉換RS232接口器件CH341T實現驅動控制系統與PC的實時通訊，標記控制系統可升級到USB接口。采用基于ATmega16的相頻修正PWM替換555振蕩電路產生的PWM，可直接通過軟件調整PWM信號。使用達林頓三極管TIP122替代直流繼電器驅動高頻電磁閥，使得電磁閥驅動電路簡單，成本低廉。該控制系統已成功應用于氣動標記機。
Abstract:
In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
提出一種基于C8051F040的炮塔方位角測試系統的設計方案，給出測試系統的各個模塊軟硬件設計。炮塔方位角測試系統集數據采集，數據傳輸和數據顯示等功能于一體，實現了炮塔方位角裝置的離線檢測。系統軟件采用C51編寫，對單片機進行有效電源管理，保證了系統的穩定性，可靠性。
Abstract:
This paper puts forwards a design of artillery position system based on C8051F040，describes all modules hardware and software design of measurement system.The system has the function of information collection，transmission，and display.It can measure artillery position system in offline.The system software using C51can manage the power of single chip microcomputer，guarantee the stability，reliability.
介紹基于VHDL的微型打印機控制器的設計。論述了微型打印機的基本原理，以及實現控制器的VHDL語言設計。打印機的數據來自系統中的存儲模塊，根據需要控制打印。該微型打印機控制器可取代傳統的微型打印機,且抗干擾性好,可靠性高，具有較強的移植性，稍加改動就可應用于不同場合。
Abstract:
This paper introduced the design method of micro printer controller based on VHDL.The basic principles of microprinter is explained,as well as the realization of the controller by VHDL language.The printer data is from the system memory modules,can control printer.The design of microprinter controller has antigood and high reliability，it can replace the traditional printer.The controller has very good portability,and need little modify that can use in different situation.
介紹一種多功能音樂播放器，它是以AT89S52單片機為核心，并輔有一些外圍器件，采用匯編語言編寫程序，實現多功能音樂播放，歌曲自動循環播放和使用琴鍵自編曲目功能。此外，彩燈顯示歌曲節奏，按鍵跳轉到喜愛曲目，液晶顯示當前播英文曲目。并給出了系統軟硬件設計。
Abstract:
It introduces a multifunctional music player,taking AT89S52 single-chip microcomputer as hardware control core and using some peripheral elements.Programmes are compiled in assembly language to act as expected.There are two functional modes in this system.One is to make the music play automatically and consecutively,the other is to compose new songs through keys.In addition,lights show the pace of music and the English names can be displayed in the liquid crystal screen.With perfect combination of hardware and software,the music player can meet many music lovers’needs for multifunctional music player.And the hardware and software of the system are given.
介紹一種基于C8051F060單片機和NAND Flash的數據采集存儲系統，該系統可實現3路信號采樣，每路采樣率為5KS/s,通過異步串行通信接口實現數據傳輸。并詳細說明系統的軟件設計。
Abstract:
An acquisition and storage system based on C8051F060and NAND Flash is designed in this paper.The system is used to sample three-channel of signal,5KSPS each channel,and can upload data to test bench through UART（Universal Asynchronous Receiver/Transmitter）.The software design is discussed in detail.
