The MAX2870 ultra-wideband phase-locked loop (PLL) and voltagecontrol oscillator (VCO) can operate in both integer-N and fractional-Nmodes, similar to the Analog Devices ADF4350 wideband synthesizer.This application note compares the MAX2870 and ADF4350 registers andloop filter design in detail. Users who already familiar with ADF4350 canuse this application note as a quick design reference.
上傳時間： 2014-12-23
上傳用戶：變形金剛
Abstract: A digital RF modulator, an integrated solution that satisfies stringent DOCSIS RF-performancerequirements, takes advantage of modern technologies like high-performance wideband digital-to-analogconversion and CMOS technology scaling. This application note describes the concept and advantages ofa digital quadrature amplitude modulation (QAM) modulator that uses the direct-RF architecture to enablea cable access platform (CCAP) system.
上傳時間： 2013-10-20
上傳用戶：drink！
Maxim Analog Essentials are a series of plug-in peripheral modules that allow engineers to quickly test, evaluate, and integrate Maxim components into their hardware/software designs. The modules electrically and physically conform to the Digilent Pmod™ interface specification and are compatible with any Digilent Pmod-compatible header.
標簽： 模擬技術
上傳時間： 2013-11-14
上傳用戶：ljj722
The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these switches combine high-voltage bilateral MOSswitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
上傳時間： 2013-10-09
上傳用戶：yepeng139
A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.
上傳時間： 2013-10-31
上傳用戶：masochism
Abstract: If sensitive analog systems are run from one supply without the sufficient bypassing to eliminate noise,
上傳時間： 2013-11-23
上傳用戶：qiulin1010
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上傳時間： 2013-11-13
上傳用戶：ca05991270
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上傳時間： 2014-12-23
上傳用戶：781354052
基于數字微鏡器件（Digital Micro-mirror Device，DMD）的哈達瑪變換光譜技術是一種新型的光譜成像技術，在國內很少有專門的文獻介紹[1-3]。文中先介紹了本實驗采用的哈達瑪光譜儀樣機的原理以及哈達瑪成像光譜儀優于傳統模板的獨特之處，即獲得多通道高能量高信噪比的光譜數據，然后描述對采集到的數據做高信噪比，高分辨率壓縮處理，最后說明此方法實時性強、圖像失真小、實用價值高、應用范圍廣。
上傳時間： 2013-11-25
上傳用戶：eastimage
Digital convergence, in recent history, has been prevalentin the consumer equipment domain and the designengineers in this area have been struggling with a plethoraof emerging standards and protocols. What lessons can welearn from their struggle? The same dilemmas now existin in-vehicle telematics and infotainment systems but withthe added issues of extremes of temperature, safety,security, and time in market.
上傳時間： 2014-12-23
上傳用戶：9牛10
