Finite state machines are widely used in digital circuit designs. Generally, when designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
標簽： Creating Machines Mentor State
上傳時間： 2013-10-08
上傳用戶：wangzhen1990
介紹高速電路的設計
標簽： High-speed Digital Design 高速數字
上傳時間： 2013-10-16
上傳用戶：yt1993410
特點（FEATURES） 精確度0.03%滿刻度（Accuracy 0.03%F.S.） 頻率輸入范圍0.01Hz至80KHz（Input range from 0.01 Hz to 80KHz） 16 BIT 隔離類比輸出（16 bit DAC isolating analog output） 輸入與輸出1/輸出2絕緣耐壓 2仟伏特/1分鐘（Dielectric strength 2KVac/1min.（input/output1/output2）） 寬范圍交直流兩用電源設計（Wide input range for auxiliary power） 尺寸小，穩定性高（Dimension small & High stability）
上傳時間： 2013-10-21
上傳用戶：dljwq
特點(FEATURES) 精確度0.1%滿刻度 (Accuracy 0.1%F.S.) 可作各式數學演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 類比輸出功能(16 bit DAC isolating analog output function) 輸入/輸出1/輸出2絕緣耐壓2仟伏特/1分鐘(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 寬范圍交直流兩用電源設計(Wide input range for auxiliary power) 尺寸小,穩定性高(Dimension small and High stability)
上傳時間： 2013-11-24
上傳用戶：541657925
針對TI公司最新發布的TMS320C6678 DSP設計出一種實用有效的電源。采用統一的12 V電源供電，制作出滿足電壓幅值要求與時序要求的開關電源。該設計主要由各類電源轉換電路組成，并通過使用Fusion Digital Power Designer軟件對電源芯片進行編程。仿真結果表明，該電源工作穩定，各方面的參數均符合要求。
上傳時間： 2013-10-12
上傳用戶：asdstation
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上傳時間： 2013-10-31
上傳用戶：caiguoqing
Abstract: Field-programmable gate arrays (FPGAs) are used in a wide variety of applications and end markets, including digital signalprocessing, medical imaging, and high-performance computing. This application note outlines the issues related to powering FPGAs.It also discusses Maxim's solutions for powering Altera® FPGAs.
上傳時間： 2013-11-02
上傳用戶：zhaoman32
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上傳時間： 2013-10-23
上傳用戶：wuchunzhong
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間： 2013-11-18
上傳用戶：hulee
In predominantly digital systems it is often necessaryto include linear circuit functions. Traditionally, separatepower supplies have been used to run the linear components(see Box, “Linear Power Supplies—Past, Present,and Future”).
標簽： Designing Operation Circuits Linear
上傳時間： 2013-11-04
上傳用戶：sdq_123
